Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › AIR FUEL RATIO SENSOR (for Sensor 2) › from 2021.07
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442029 AIR FUEL RATIO SENSOR(for Sensor 2) A

M15A-FKS ENGINE CONTROL  AIR FUEL RATIO SENSOR(for Sensor 2)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A459215N04
1.156,0.208 6.302,3.125 5.146,2.917 1.146,3.333 6.313,5.74 5.167,2.406 4.802,5.313 5.635,5.646 0.833,0.333 4.833,1.51 5.667,1.844 0.833,0.333 3.563,2.292 3.99,2.292 false 3.604,5.302 4.229,5.302 false 4.49,4.99 4.656,5.469 4.656,5.469 4.792,5.469 false 4.573,1.854 4.698,1.667 4.698,1.667 4.833,1.667 false 1.219,0.292 1.594,0.531 0.375,0.24 12 false *A 1.219,3.396 1.594,3.635 0.375,0.24 12 false *B 6.083,1.583 6.448,1.896 0.365,0.313 18 false 1 3.365,2.156 3.729,2.469 0.365,0.313 18 false 2 6.073,5.375 6.438,5.688 0.365,0.313 18 false 1 3.385,5.146 3.75,5.458 0.365,0.313 18 false 2 4.906,5.333 5.677,5.583 0.771,0.25 8 false 44 (449, 32) 4.865,5.479 5.75,5.729 0.885,0.25 8 false 37.7 (384, 28)* 4.948,1.531 5.719,1.781 0.771,0.25 8 false 44 (449, 32) 4.896,1.677 5.781,1.927 0.885,0.25 8 false 37.7 (384, 28)*

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 2 AIR FUEL RATIO SENSOR 89467C (Click here) - -
2 WIRE HARNESS CLAMP BRACKET - (Click here) - -

*A for 2WD *B for AWD
V100146

N*m (kgf*cm, ft.*lbf): Specified torque * For use with SST

A485885N01
0.167,0.667 7.083,2.667 6.917,2 3.635,2.333 4.635,2.5 1,0.167 5.208,2.417 6.208,2.583 1,0.167 2.021,2.219 3.021,2.385 1,0.167 0.438,2.333 1.438,2.5 1,0.167 6.25,2.063 6.917,2.229 0.667,0.167 1.75,2.052 1.75,1.719 false 4.885,2.104 4.885,1.771 false 6.833,0.167 6.5,0.167 false 3.5,2.667 3.5,0.667 false 6.5,0.865 6.167,0.865 false 6.771,0.5 6.438,0.5 false 4.135,2 4.135,2.333 false 0.938,2 0.938,2.333 false 2.521,1.885 2.521,2.219 false 5.719,2.083 5.719,2.417 false 6.583,1.729 6.583,2.063 false 1.677,2.083 1.958,2.438 0.281,0.354 18 false 4 4.823,2.115 5.104,2.469 0.281,0.354 18 false 4 6.542,0.667 6.823,1.021 0.281,0.354 18 false 3 6.677,1.583 6.99,1.781 0.313,0.198 10 false x2 5.802,1.958 6.115,2.156 0.313,0.198 10 false x2 4.24,1.875 4.552,2.073 0.313,0.198 10 false x2 2.604,1.76 2.917,1.958 0.313,0.198 10 false x2 1.031,1.854 1.344,2.052 0.313,0.198 10 false x2 0.208,0.688 0.583,0.927 0.375,0.24 12 false *A 3.542,0.698 3.917,0.938 0.375,0.24 12 false *B 6.302,0 6.583,0.354 0.281,0.354 18 false 5 6.25,0.333 6.531,0.688 0.281,0.354 18 false 6 2.052,2.219 3.021,2.385 0.969,0.167 8 false 5.0 (51, 44 in.*lbf) 0.479,2.333 1.448,2.5 0.969,0.167 8 false 5.0 (51, 44 in.*lbf) 3.677,2.333 4.646,2.5 0.969,0.167 8 false 5.0 (51, 44 in.*lbf) 6.281,2.063 7,2.229 0.719,0.167 8 false 22 (224, 16) 5.26,2.417 6.229,2.583 0.969,0.167 8 false 5.0 (51, 44 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

3 CENTER NO. 1 FLOOR BRACE 57543C - - -
4 CENTER NO. 4 ENGINE UNDER COVER 51447D - - -
5 INSPECT FOR EXHAUST GAS LEAK - (Click here) - -
6 PERFORM INITIALIZATION - - - (Click here)

*A for TMC Made *B for TMMF Made
V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

PROCEDURE

Hide 89467C 1.INSTALL NO. 2 AIR FUEL RATIO SENSOR

a.

for 2WD:

A458063C03
5.667,1.073 5.427,0.781 true 0.26,0.083 0.76,0.365 0.5,0.281 18 false ii, iii 4.448,0.167 4.656,0.438 0.208,0.271 18 true i 5.667,1 5.969,1.188 0.302,0.188 10 true SST 4.219,1.417 4.427,1.604 0.208,0.188 10 true *a
*a Torque Wrench Fulcrum Length - -


i.

Using SST, install the No. 2 air fuel ratio sensor to the front exhaust pipe assembly.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the No. 2 air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




ii.

Engage the 2 wire harness clamps.

NOTICE:

Make sure the white tube is between the wires.



iii.

Connect the No. 2 air fuel ratio sensor connector.



b.

for AWD:

A485882C01
2.594,0.417 2.385,0.573 true 5.927,1.615 6.135,1.865 0.208,0.25 18 true ii 0.385,0.021 0.594,0.292 0.208,0.271 18 true i 2.635,0.333 2.938,0.521 0.302,0.188 10 true SST 3.24,1.333 3.448,1.521 0.208,0.188 10 true *a 4.573,1.271 4.781,1.521 0.208,0.25 18 true iii
*a Torque Wrench Fulcrum Length - -


i.

Using SST, install the No. 2 air fuel ratio sensor to the front exhaust pipe assembly.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the No. 2 air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




ii.

Engage the 3 wire harness clamps.

NOTICE:

Make sure the white tube is between the wires.



iii.

Connect the No. 2 air fuel ratio sensor connector.



Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.

for 2WD:

A458064C02
0.604,0.156 1.979,0.51 1.375,0.354 18 false i, ii 2.99,0.25 3.302,0.448 0.313,0.198 10 false *a 4.344,0.26 4.656,0.458 0.313,0.198 10 false *b 2.417,1.052 2.729,1.25 0.313,0.198 10 false *c 3.823,1.052 4.135,1.25 0.313,0.198 10 false *c
*a Correct *b Incorrect
*c Standard Position - -


i.

Install the wire harness clamp bracket to the No. 2 air fuel ratio sensor.

NOTICE:

Aline the edge of the wire harness clamp bracket and No. 2 air fuel ratio sensor as shown in the illustration.



ii.

Engage the guide to connect the wire harness to the wire harness clamp bracket.



b.

for AWD:

A485881C01
1.854,0.073 2.344,0.396 0.49,0.323 18 false i, ii 4.74,0.25 5,0.469 0.26,0.219 10 false *a 5.823,0.25 6.083,0.469 0.26,0.219 10 false *b 5.156,0.125 5.417,0.344 0.26,0.219 10 false *c 6.292,0.125 6.552,0.344 0.26,0.219 10 false *c
*a Correct *b Incorrect
*c Standard Position - -


i.

Install the wire harness clamp bracket to the No. 2 air fuel ratio sensor.

NOTICE:

Aline the edge of the wire harness clamp bracket and No. 2 air fuel ratio sensor as shown in the illustration.



ii.

Engage the guide to connect the wire harness to the wire harness clamp bracket.



Hide 57543C 3.INSTALL CENTER NO. 1 FLOOR BRACE (for TMMF Made)

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)

Hide 51447D 4.INSTALL CENTER NO. 4 ENGINE UNDER COVER

Hide 6.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the No. 2 air fuel ratio sensor.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION