Home › Engine / Hybrid System › STOP AND START › BACKUP BOOST CONVERTER › from 2021.07
RM3700E _51 Engine / Hybrid System _105429 STOP AND START _0482031 BACKUP BOOST CONVERTER A

STOP AND START  BACKUP BOOST CONVERTER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A485873N01
6.469,0.229 6.802,0.229 false 6.438,0.625 6.771,0.625 false 1.302,2.51 1.594,2.083 1.594,2.083 1.76,2.083 false 4.396,3.719 4.396,4.052 false 5.135,3.396 5.135,3.729 false 6.219,0.063 6.458,0.333 0.24,0.271 18 true 1 6.219,0.448 6.417,0.74 0.198,0.292 18 true 2 1.813,1.927 2.094,2.281 0.281,0.354 18 false 3 4.333,4.063 4.615,4.417 0.281,0.354 18 false 4 5.063,3.76 5.344,4.115 0.281,0.354 18 false 5 5.792,3.458 6.104,3.656 0.313,0.198 10 false x2 5.76,2.979 6.073,3.177 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 FRONT BUMPER ASSEMBLY - - - -
4 ECO RUN VEHICLE CONVERTER ASSEMBLY G92C0A (Click here) - -
5 NO. 1 CONVERTER CONTROL BRACKET F1334 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during backup boost converter removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 3.REMOVE FRONT BUMPER ASSEMBLY

Hide G92C0A 4.REMOVE ECO RUN VEHICLE CONVERTER ASSEMBLY

a.
A475400C02
3.521,0.417 3.427,0.188 false 3.76,1.354 3.667,1.458 false 3.26,0.104 3.458,0.271 0.198,0.167 10 false *a 3.792,1.25 3.99,1.417 0.198,0.167 10 false *a 0.385,0.052 0.542,0.385 0.156,0.333 18 true i 4.219,0.042 4.438,0.313 0.219,0.271 18 true ii
*a Lock Lever - -


i.

Move the lock lever as shown in the illustration and disconnect the eco run vehicle converter assembly connector.


ii.

Remove the bolt, nut and eco run vehicle converter assembly.



Hide F1334 5.REMOVE NO. 1 CONVERTER CONTROL BRACKET

a.
A475402