Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER › from 2021.07
RM3700E _59 Vehicle Exterior _093282 EXTERIOR PANELS / TRIM _0440163 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B590018N02
0.958,4.969 0.958,4.542 false 2.073,0.635 2.406,0.635 false 5.51,4.531 5.927,4.531 false 2.49,0.521 2.771,0.885 0.281,0.365 18 false 2 1,4.927 1.281,5.281 0.281,0.354 18 false 3 5.969,4.417 6.25,4.771 0.281,0.354 18 false 1 1.698,5.333 1.979,5.521 0.281,0.188 10 false x4 2.177,2.979 2.458,3.167 0.281,0.188 10 false x2 1.333,2.479 1.615,2.667 0.281,0.188 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT FENDER MOULDING SUB-ASSEMBLY LH 75602A - - -
2 FRONT FENDER MOULDING SUB-ASSEMBLY RH 75601A - - -
3 FRONT BUMPER ASSEMBLY - (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front bumper assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
w/ Parking Support Brake System:

Front bumper assembly (Including removal and installation)


·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA parking assist-sensor system (w/ Parking Support Brake System)

·

Parking support brake system

·

Advanced Park (w/ Advanced Park)


w/o Advanced Park:(Click here)
w/ Advanced Park:(Click here)
Front television camera view adjustment Panoramic view monitor system w/o Advanced Park:(Click here)
w/ Advanced Park:(Click here)

PROCEDURE

Hide 75602A 1.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY LH

Hide 75601A 2.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH

a.

Use the same procedure as for the LH side.


Hide 3.REMOVE FRONT BUMPER ASSEMBLY

a.
B590021C02
0.417,0.135 0.698,0.49 0.281,0.354 18 false i 2.125,2.188 2.406,2.542 0.281,0.354 18 false ii 0.375,3.958 0.656,4.313 0.281,0.354 18 false iii
V113147

Remove in this Direction - -


i.

Apply protective tape around the front bumper assembly.


ii.

Remove the 4 screws.


iii.

Disengage the claws as shown in the illustration.



b.
B590023C02
0.927,0.115 1.208,0.469 0.281,0.354 18 false i 0.323,2.979 0.604,3.333 0.281,0.354 18 false ii 3.615,2.99 4.219,3.313 0.604,0.323 18 true iii, iv 4.104,3.365 4.313,3.563 0.208,0.198 10 true *a 6.25,3.354 6.469,3.563 0.219,0.208 10 true *a 4.979,3.573 5.188,3.792 0.208,0.219 10 true *b 5.385,3.563 5.583,3.781 0.198,0.219 10 true *b
*a Clip *b Bolt


i.

Pull back the side of the front bumper assembly to disconnect the 3 connectors.

NOTICE:

Do not apply excessive force when pulling back the front bumper assembly.



ii.

Disconnect the 2 connectors.


iii.

Remove the 2 screws and 2 bolts.


iv.

Remove the front bumper assembly.