Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2021.07
RM3700E _51 Engine / Hybrid System _105429 STOP AND START _0482038 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P060629  Backup Boost Converter "A" Control CPU Signal Invalid  


DESCRIPTION

The engine stop and start ECU can detect open circuits when signals such as the boost, standby request or overheating signal cannot be sent to the backup boost converter control IC from the stop and start control IC in the engine stop and start ECU.

If a CPU duty malfunction is detected, the engine stop and start ECU stores DTC P060629 and blinks the stop and start cancel indicator.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory DTC Output from Priority Note
P060629 Backup Boost Converter "A" Control CPU Signal Invalid The following condition continues for 1 second or more (2 trip detection logic):
·

CPU duty malfunction is detected.


·

Wire harness or connector

·

Engine stop and start ECU


Blinks DTC stored Stop and Start A SAE Code: P0606

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the auxiliary battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Auxiliary Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the auxiliary battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Auxiliary Battery Charge Control cannot be checked, charge the auxiliary battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

b.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



c.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


d.

Keep the engine stopped by stop and start control for 1 second or more.


e.

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the auxiliary battery voltage is low.



f.

Check that DTCs are not output.

Powertrain > Stop and Start > Trouble Codes
50001 392


STOP AND START SYSTEM OPERATION CHECK


Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK


WIRING DIAGRAM

A440335E09
2.979,0.99 4.208,1.188 1.229,0.198 10 false BBC NO. 1 2.979,1.417 4.208,1.615 1.229,0.198 10 false BBC NO. 2 0.833,1.604 2.281,2.031 1.448,0.427 10 false BATT-MAIN NO. 1 5.896,0.865 7.156,1.063 1.26,0.198 10 false BIN1 5.896,1.25 7.156,1.448 1.26,0.198 10 false BIN2 5.875,1.781 7.135,1.979 1.26,0.198 10 false GND1 5.865,2.365 7.125,2.563 1.26,0.198 10 false GND2 5.688,0.74 6.948,0.938 1.26,0.198 10 false 3 5.688,1.156 6.948,1.354 1.26,0.198 10 false 1 5.698,1.667 6.958,1.865 1.26,0.198 10 false 8 5.719,2.229 6.979,2.427 1.26,0.198 10 false 2 5.625,2.729 6.885,2.927 1.26,0.198 10 false A66 5.615,2.885 7,3.344 1.385,0.458 10 false Engine Stop and Start ECU 0.969,2.25 2.271,2.667 1.302,0.417 10 false Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

For wire harness and connector inspection procedures and precautions, refer to "Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING"

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - AUXILIARY BATTERY)

Pre-procedure1

a.

Disconnect the engine stop and start ECU connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A66)Location & Routing

Click Connector(A66)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECU

A66-1 (BIN2) - Body ground Always 9.5 to 14 V
A66-3 (BIN1) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

Pre-procedure1

a.

Disconnect the A66 engine stop and start ECU connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A66)Location & Routing

Click Connector(A66)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECU

A66-2 (GND2) - Body ground Always Below 1 Ω
A66-8 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR