| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | NO. 2 ANTENNA CORD SUB-ASSEMBLY | 86101J | ( )
|
- | - |
| 2 | NO. 2 ANTENNA CORD SUB-ASSEMBLY | 86101J | ( )
|
- | - |
| *A | for Normal Roof | *B | for Panoramic Moon Roof |
| *C | w/ Digital Audio Broadcasting Antenna | *D | w/o Digital Audio Broadcasting Antenna |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 3 | NO. 1 ROOF WIRE | 82171 | ( )
|
- | - |
| 4 | NO. 1 ROOF WIRE | 82171 | ( )
|
- | - |
| *A | for Normal Roof | *B | for Panoramic Moon Roof |
| *C | for TMC Made | *D | for TMMF Made |
| *E | w/ Vanity Light | *F | w/ Pre-collision System or Rain Sensor or EC Mirror |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 5 | NO. 3 ROOF SILENCER PAD | 63343 | ( )
|
- | - |
| 6 | NO. 1 ROOF SILENCER PAD | 63341 | ( )
|
- | - |
| 7 | NO. 2 ROOF SILENCER PAD | 63342 | ( )
|
- | - |
| 8 | NO. 5 ROOF SILENCER PAD | 63345 | ( )
|
- | - |
| *A | for Normal Roof | - | - |
82171
3.INSTALL NO. 1 ROOF WIRE (for Normal Roof)
w/ Vanity Light:
|
Connect in this Direction | - | - |
Turn the visor connector approximately 90° clockwise to connect the visor connector as shown in the illustration.
for TMC Made:
| *a | Positioning Tape | *b | Marking |
Line up the No. 1 roof wire positioning tape and the roof headlining markings.
for TMC Made:
| *a | Adjustment Area | - | - |
Install the No. 1 roof wire with new pieces of adhesive tape.
Apply the tape securely in place.
Do not touch the adhesive surface when applying the tape to prevent adhesion failure.
Adjust the slack of the No. 1 roof wire as shown in the adjustment area of illustration.
for TMMF Made:
| *a | Positioning Tape | *b | Marking |
Line up the No. 1 roof wire positioning tape and the roof headlining markings.
for TMMF Made:
| *A | w/ Rain Sensor | *B | w/ Pre-collision System or EC Mirror |
| *C | w/ Vanity Light | - | - |
| *a | Adjustment Area | - | - |
Install the No. 1 roof wire with new pieces of adhesive tape.
Apply the tape securely in place.
Do not touch the adhesive surface when applying the tape to prevent adhesion failure.
Adjust the slack of the No. 1 roof wire as shown in the adjustment area of illustration.
82171
4.INSTALL NO. 1 ROOF WIRE (for Panoramic Moon Roof)
| *a | Positioning Tape | *b | Marking |
Line up the No. 1 roof wire positioning tape and the roof headlining markings.
| *A | w/ Rain Sensor | *B | w/ Pre-collision System or EC Mirror |
| *a | Adjustment Area | - | - |
Install the No. 1 roof wire with new pieces of adhesive tape.
Apply the tape securely in place.
Do not touch the adhesive surface when applying the tape to prevent adhesion failure.
Adjust the slack of the No. 1 roof wire as shown in the adjustment area of illustration.
63343
5.INSTALL NO. 3 ROOF SILENCER PAD (for Normal Roof)
| *a | Marking | - | - |
Align the markings on the roof headlining with the No. 3 roof silencer pad and install them using hot melt glue.
63341
6.INSTALL NO. 1 ROOF SILENCER PAD (for Normal Roof)
| *a | Marking | - | - |
Align the markings on the roof headlining with the 3 No. 1 roof silencer pads and install them using hot melt glue.
63342
7.INSTALL NO. 2 ROOF SILENCER PAD (for Normal Roof)
| *a | Marking | - | - |
Align the markings on the roof headlining with the No. 2 roof silencer pad and install them using hot melt glue.
63345
8.INSTALL NO. 5 ROOF SILENCER PAD (for Normal Roof)
| *a | Marking | - | - |
Align the markings on the roof headlining with the 2 No. 5 roof silencer pads and install them using hot melt glue.