| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | NO. 1 WINDSHIELD WIPER SHAFT COVER | - | - | - | - |
| 2 | WINDSHIELD WIPER MOTOR ASSEMBLY | 85110 | ( )
|
- | - |
| 3 | WINDSHIELD WIPER MOTOR ASSEMBLY | 85110 | ( )
|
- | - |
| *A | for LHD | *B | for RHD |
| *C | for TMMF Made | - | - |
| *1 | WINDSHIELD WIPER LINK ASSEMBLY | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
|
MP grease |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
Use the same procedure for RHD and LHD vehicles.
The procedure below is for LHD vehicles.
85112A
1.INSTALL NO. 1 WINDSHIELD WIPER SHAFT COVER (for TMMF Made)
85110
2.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY (for LHD)
| *a | Pivot of Windshield Wiper Motor Assembly | *b | No. 1 Windshield Wiper Link Rod |
|
MP grease |
|
Install in this Direction (1) |
|
Install in this Direction (2) | - | - |
Temporarily install the windshield wiper motor assembly to the wiper link assembly as shown in the illustration.
Install the windshield wiper motor assembly with the 3 bolts.
Apply MP grease to the pivot of the windshield wiper motor assembly.
Connect the No. 1 windshield wiper link rod to the pivot of the windshield wiper motor assembly.
85110
3.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY (for RHD)
| *a | Pivot of Windshield Wiper Motor Assembly | *b | No. 1 Windshield Wiper Link Rod |
|
MP grease | - | - |
Engage the guides to install the windshield wiper motor assembly.
Using a T30 "TORX" socket wrench, install the 2 screws.
Apply MP grease to the pivot of the windshield wiper motor assembly.
Connect the No. 1 windshield wiper link rod to the pivot of the windshield wiper motor assembly.
4.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
|
|
55708
5.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
|
|
53867
6.INSTALL FRONT FENDER TO COWL SIDE SEAL LH
53866
7.INSTALL FRONT FENDER TO COWL SIDE SEAL RH
8.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
| *a | Serration | *b | Alignment Mark |
When reusing the front wiper arm and blade assembly LH:
1. Clean the wiper arm serrations to remove any burrs, dirt, etc.
Do not grind down the wiper arm serrations.
When reusing the windshield wiper motor and link assembly:
1. Clean the wiper pivot serrations with a wire brush.
Do not grind down the wiper pivot serrations.
Set the automatic stop position by the below procedure.
1. Turn the ignition switch on.
2. Operate the windshield wiper motor assembly and stop the windshield wiper motor and link assembly at the automatic stop position.
3. Turn the ignition switch off.
Install the front wiper arm and blade assembly LH to the position shown in the illustration.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 10 mm (0.394 in.) | - | - |
Hold the wiper arm by hand to install the nut.
9.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
| *a | Serration | *b | Alignment Mark |
When reusing the front wiper arm and blade assembly RH:
1. Clean the front wiper arm serrations to remove any burrs, dirt, etc.
Do not grind down the wiper arm serrations.
When reusing the windshield wiper motor and link assembly:
1. Clean the wiper pivot serrations with a wire brush.
Do not grind down the wiper pivot serrations.
Install the front wiper arm and blade assembly RH to the position as shown in the illustration.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 10 mm (0.394 in.) | - | - |
Hold the wiper arm by hand to install the nut.
10.INSPECT FRONT WIPER ARM AND BLADE ASSEMBLY
85292B
11.INSTALL FRONT WIPER ARM HEAD CAP