Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › SHIFT LEVER (for TMMF Made) › from 2021.07
RM3700E _52 Drivetrain _093735 P910 HYBRID TRANSMISSION / TRANSAXLE _0482421 SHIFT LEVER(for TMMF Made) A

P910 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER(for TMMF Made)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C462309N01
3.458,4.781 4.125,4.948 0.667,0.167 6.469,0.24 6.802,0.24 false 5.938,3.521 6.24,3.521 false 3.594,2.396 3.927,2.396 false 3.75,4.469 3.677,4.031 3.677,4.031 3.51,4.031 false 5.792,4.135 6.198,4.135 false 5.75,3.01 6.052,3.01 false 4.125,4.865 4.427,4.865 false 6.542,4.01 6.823,4.365 0.281,0.354 18 false 1 6.292,3.385 6.573,3.74 0.281,0.354 18 false 5 6.333,2.875 6.615,3.229 0.281,0.354 18 false 4 4.01,2.271 4.292,2.625 0.281,0.354 18 false 3 3.313,3.896 3.594,4.25 0.281,0.354 18 false 2 6,0.104 6.604,0.458 0.604,0.354 18 false 6, 7 4.583,4.813 4.896,5.01 0.313,0.198 10 false x4 3.521,4.792 4.219,5.031 0.698,0.24 8 false 12 (122, 9)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 TRANSMISSION FLOOR SHIFT ASSEMBLY - (Click here) - -
2 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -
3 REAR CONSOLE BOX ASSEMBLY 58910C - - -
4 SHIFT LEVER KNOB SUB-ASSEMBLY 33504F (Click here) - -
5 SHIFT LEVER CAP 33554 - - -
6 INSPECT SHIFT LEVER POSITION - (Click here) - -
7 ADJUST SHIFT LEVER POSITION - (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

PROCEDURE

Hide 1.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

a.

for LHD:

C462319N01
3.115,1.646 3.25,1.813 0.135,0.167 10 true 1 4,0.542 4.135,0.708 0.135,0.167 10 true 2 2.823,0.917 2.958,1.083 0.135,0.167 10 true 3 4.302,1.385 4.438,1.552 0.135,0.167 10 true 4 1.958,0.083 2.344,0.396 0.385,0.313 18 true i, ii 0.125,2.021 0.667,2.302 0.542,0.281 18 true iii, iv 3.51,2.021 4.052,2.302 0.542,0.281 18 true v, vi

i.

Temporarily install the transmission floor shift assembly to the vehicle body with the 4 bolts.


ii.

Fully tighten the 4 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


iii.

Engage the 2 clamps to install the wire harness to the transmission floor shift assembly.


iv.

Connect the connector.


v.

Engage the clamp to connect the wire harness to the transmission floor shift assembly.


vi.

Connect the 2 connectors.



b.

for LHD:

C462320N01
3.073,1.646 3.208,1.813 0.135,0.167 10 true 1 3.938,0.521 4.073,0.688 0.135,0.167 10 true 2 2.781,0.896 2.917,1.063 0.135,0.167 10 true 3 4.229,1.385 4.365,1.552 0.135,0.167 10 true 4 1.958,0.083 2.344,0.396 0.385,0.313 18 true i, ii 0.125,2.021 0.667,2.302 0.542,0.281 18 true iii, iv 3.51,2.021 4.052,2.302 0.542,0.281 18 true v, vi

i.

Temporarily install the transmission floor shift assembly to the vehicle body with the 4 bolts.


ii.

Fully tighten the 4 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


iii.

Engage the 2 clamps to install the wire harness to the transmission floor shift assembly.


iv.

Connect the 2 connectors.


v.

Engage the clamp to connect the wire harness to the transmission floor shift assembly.


vi.

Connect the connector.



Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Z101186

NOTICE:

Before connecting the transmission control cable assembly, check that the shift lever is in N.



a.
C462311C01
1.917,2.01 1.729,1.635 false 6.094,0.948 5.833,0.625 false 5.688,1.156 5.5,0.781 true 0.417,0.083 0.698,0.438 0.281,0.354 18 false i 4.083,0.083 4.365,0.438 0.281,0.354 18 false ii 1.865,2.042 2.177,2.24 0.313,0.198 10 false *1 5.656,1.177 5.969,1.375 0.313,0.198 10 false *2 6.052,0.969 6.365,1.167 0.313,0.198 10 false *3
*1 Adjuster Case *2 Adjuster Case Cover
*3 Lock Piece - -


i.

Slide the adjuster case cover in the direction shown by the arrow.


ii.

Using a precision screwdriver, pull out the lock piece of the adjuster case.



b.
C462312C01
2.073,1.115 2.917,1.573 2.917,1.573 2.188,2.271 true 4.271,0.677 4.531,0.781 false 5.604,0.667 5.865,0.771 false 2.021,1.469 2.313,1.594 false 0.417,0.25 0.698,0.552 0.281,0.302 18 false i 3.698,0.25 3.979,0.552 0.281,0.302 18 false ii 1.875,4.031 2.25,4.333 0.375,0.302 18 false iii 2.115,0.563 2.427,0.76 0.313,0.198 10 false *a 2.365,1.521 2.677,1.719 0.313,0.198 10 false *1 2.969,1.479 3.281,1.677 0.313,0.198 10 false *2 4.104,0.583 4.417,0.781 0.313,0.198 10 false *2 5.438,0.573 5.75,0.771 0.313,0.198 10 false *2
*1 Lock Nut *2 Stopper
*a Push in - -


i.

Rotate the lock nut counterclockwise approximately 180° and, while holding the lock nut in that position, push in the stopper.

NOTICE:

Do not rotate the nut excessively as the interior spring may come off and the transmission control cable assembly will not be reusable.



ii.

Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

After installation, check that the outer part of the stopper is as shown in the illustration.

·

Do not forcibly pull the floor shift transmission control select cable into the cabin.




iii.

Connect the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Push the end of the transmission control cable assembly all the way to the base of the transmission floor shift assembly pin.

·

Connect the transmission control cable assembly so that the lock piece faces the driver side.





c.
C462313C01
4.24,0.719 4.563,0.896 true 4.01,0.813 4.302,1.063 true 2.042,2.833 2.333,3.083 true 4.323,0.99 4.531,1.188 0.208,0.198 10 true *1 2.083,0.094 2.365,0.448 0.281,0.354 18 false i 0.354,2.01 0.635,2.365 0.281,0.354 18 false ii 4.583,0.813 4.792,1.01 0.208,0.198 10 true *2 2.354,3.01 2.563,3.208 0.208,0.198 10 true *3
*1 Lock Piece *2 Adjuster Case
*3 Adjuster Case Cover - -


i.

Push in the lock piece of the adjuster case to lock it.

NOTICE:
C414646C05
1.771,0.365 2.177,0.365 false 0.667,1.167 0.792,1.167 0.792,1.167 1.042,1.698 true 0.469,1.063 0.708,1.333 0.24,0.271 10 false *1 1.552,0.229 1.875,0.469 0.323,0.24 10 false *2
*1 Transmission Control Cable Assembly
*2 Lever Shaft


·

When pushing in the lock piece of the adjuster case to lock it, remove your hand from the lever shaft.

·

When pushing in the lock piece of the adjuster case to lock it, do not move the lever shaft or transmission control cable assembly forward or backward.




ii.

Move the adjuster case cover in the direction shown by the arrow.

NOTICE:

If the adjuster case cover is not moved far enough so that the adjuster case cover engages the lock piece, the cable will not be able to lock, and reliable shift operation will not be possible.




Hide 58910C 3.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 33504F 4.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

Z101186

(Click here)

Hide 33554 5.INSTALL SHIFT LEVER CAP