Home › General › MAINTENANCE › REAR DISC BRAKE PAD (for TMC Made 2WD) › from 2021.07
RM3700E _V1 General _093024 MAINTENANCE _0482441 REAR DISC BRAKE PAD(for TMC Made 2WD) A

MAINTENANCE  REAR DISC BRAKE PAD(for TMC Made 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C445743N05
6.354,0.292 6.688,0.292 false 6.292,0.719 6.625,0.719 false 5.802,3.24 5.99,2.885 5.99,2.885 6.156,2.885 false 5.573,1.656 5.813,1.656 false 1.781,5.031 2.802,5.031 false 2.177,4.75 2.177,5.031 false 2.969,5.563 3.896,5.563 false 3.385,5.354 3.385,5.563 false 0.958,4.302 1.677,4.302 false 1.24,4.104 1.24,4.302 false 2.729,3.49 2.729,3.302 2.729,3.302 3.771,3.302 false 3.427,3.302 3.427,3.688 false 2.594,1.302 2.948,0.729 2.948,0.729 3.115,0.729 true 5.698,0.208 6.094,0.552 0.396,0.344 18 false , 2 6.094,0.604 6.292,0.906 0.198,0.302 18 false 3 6.229,2.76 6.51,3.115 0.281,0.354 18 false 4 6.125,1.521 6.406,1.875 0.281,0.354 18 false 5 1.604,4.896 1.885,5.25 0.281,0.354 18 false 7 0.771,4.177 1.052,4.531 0.281,0.354 18 false 8 2.771,5.448 3.063,5.76 0.292,0.313 18 false 8 5.396,0.24 6.01,0.521 0.615,0.281 12 false (*A) 5.24,0.198 5.521,0.552 0.281,0.354 18 false 1 4.292,3.219 4.573,3.573 0.281,0.354 18 false 8 4.115,3.281 4.313,3.49 0.198,0.208 10 false ● 3.458,0.594 3.74,0.948 0.281,0.354 18 false 6 6.01,0.229 6.625,0.51 0.615,0.281 12 false (*A)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - (Click here) - -
3 PERFORM REAR BRAKE PAD REPLACEMENT MODE - - - (Click here)
4 REAR WHEEL - - - -
5 NO. 2 PARKING BRAKE WIRE ASSEMBLY 890C0A (Click here) - -
6 REAR DISC BRAKE CYLINDER ASSEMBLY 47850 (Click here) - -
7 REAR DISC BRAKE PAD 04466 (Click here) - -
8 REAR DISC BRAKE ANTI-SQUEAL SHIM KIT 04946 - - -

*A for HV Model - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear disc brake pad removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC [C13CD00, C13CE00, C140000] may be stored. As there is no malfunction, clear the DTC. (for HV Model)

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)



HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used. (for HV Model)

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model)

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.

for HV Model: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model TMC Made)>PRECAUTION

for Gasoline Model: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model TMC Made)>PRECAUTION



Hide 2.DISABLE BRAKE CONTROL (for HV Model)

Z101186

Click here(Click here)

Hide 4.REMOVE REAR WHEEL

Hide 890C0A 5.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Z101186

Click here(Click here)

Hide 47850 6.SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY

Z101186

CAUTION:
C379268

·

Be careful not to get pinched by the rear disc brake cylinder assembly or other parts when removing the rear disc brake pads.

·

After lifting up the rear disc brake cylinder assembly, secure it in place before performing any work on it.

·

The rear disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.




a.
C449886N02
0.365,0.063 0.781,0.427 0.417,0.365 18 false i, ii

i.

Hold the rear disc brake cylinder slide pin (lower side) and remove the bolt.

NOTICE:

Do not kink or damage the brake line.



ii.

Pull the rear disc brake cylinder assembly upward.



Hide 04466 7.REMOVE REAR DISC BRAKE PAD

a.
C449884


Hide 04946 8.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

a.
C445746N05
0.271,0.042 0.552,0.396 0.281,0.354 18 false i 4.083,0.052 4.365,0.406 0.281,0.354 18 false ii

i.

Remove the front No. 1 disc brake anti-squeal shim and front No. 2 disc brake anti-squeal shim from each front disc brake pad.


ii.

Using a screwdriver, remove the front disc brake pad wear indicator plate from each front disc brake pad.

NOTICE:

If the rear disc brake pad wear indicator plate is removed, replace it with a new one.