Home › Brake › BRAKE (REAR) › REAR BRAKE (for TMC Made 2WD) › from 2021.07
RM3700E _54 Brake _093728 BRAKE (REAR) _0482436 REAR BRAKE(for TMC Made 2WD) A

BRAKE (REAR)  REAR BRAKE(for TMC Made 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C449769N04
6.417,0.281 6.802,0.281 false 6.417,0.656 6.771,0.656 false 6.417,1.073 6.813,1.073 false 2.354,1.271 2.74,1.271 false 4.75,4.979 5.135,4.979 false 1.281,1.813 1.281,1.469 false 3.26,0.469 3.573,0.469 false 6.229,0.51 6.594,0.865 0.365,0.354 18 false 3 6.083,0.198 6.521,0.479 0.438,0.281 12 false (*A) 6.229,0.938 6.594,1.292 0.365,0.354 18 false 5 4.573,4.844 4.938,5.198 0.365,0.354 18 false 2 3.917,0.344 4.281,0.698 0.365,0.354 18 false 6 1.344,1.865 1.708,2.219 0.365,0.354 18 false 7 2.802,1.198 3.24,1.479 0.438,0.281 10 false ● 0.729,1.042 1.146,1.417 0.417,0.375 10 false x2 5.625,0.177 6.115,0.552 0.49,0.375 18 false 1, 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 REAR WHEEL - - - -
3 PERFORM REAR BRAKE PAD REPLACEMENT MODE - (Click here) - -
4 DISABLE BRAKE CONTROL - (Click here) - -
5 BRAKE FLUID - - (Click here) -
6 NO. 2 PARKING BRAKE WIRE ASSEMBLY 89C0A (Click here) - -
7 PARKING BRAKE ACTUATOR ASSEMBLY 46310B (Click here) - -

*A for HV Model - -
● Non-reusable part - -

C445721N07
3.823,0.24 3.823,0.146 3.823,0.146 5.104,0.146 false 3.385,1.823 3.385,1.552 false 1.573,3.688 1.74,3.688 1.74,3.688 1.833,3.844 false 4.427,3.927 4.802,3.927 false 2.688,1.823 3.854,1.823 false 4.594,0.438 4.594,0.146 false 4.823,1.604 4.823,1.396 4.823,1.396 5.76,1.396 false 5.396,1.896 5.396,1.396 false 1.667,1.188 2.615,1.188 false 2.073,1.188 2.073,0.875 false 1.656,4.323 2.031,4.323 false 1.208,3.302 1.542,3.302 false 2.531,2.76 2.906,2.76 false 0,0 0.448,0.333 0.448,0.333 18 false 9 0,0 0.448,0.333 0.448,0.333 10 false ● 5.594,0.031 6.042,0.365 0.448,0.333 18 false 11 1.396,3.552 1.844,3.885 0.448,0.333 18 false 8 2.938,2.885 3.385,3.219 0.448,0.333 10 false x2 4.854,3.771 5.302,4.104 0.448,0.333 18 false 9 2.385,1.667 2.833,2 0.448,0.333 18 false 10 5.458,0.115 5.906,0.448 0.448,0.333 10 false ● 6.115,1.26 6.563,1.594 0.448,0.333 18 false 11 1.354,1.073 1.802,1.406 0.448,0.333 18 false 11 1.469,4.26 1.917,4.594 0.448,0.333 10 false ● 1.063,3.208 1.51,3.542 0.448,0.333 10 false ● 2.365,2.677 2.813,3.01 0.448,0.333 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

8 REAR FLEXIBLE HOSE 47319F - - -
9 REAR DISC BRAKE CYLINDER ASSEMBLY 47850 - - -
10 REAR DISC BRAKE PAD 04466 - - -
11 REAR DISC BRAKE ANTI-SQUEAL SHIM KIT 04946 (Click here) - -

● Non-reusable part - -

C445722N05
4.552,0.417 6.063,2.177 1.51,1.76 6.073,1.354 6.469,1.354 false 5.833,4.042 6.135,4.042 false 2.146,3.656 2.604,3.656 false 3.198,2.625 3.531,2.625 false 2.667,1.51 3.167,1.51 false 3.115,4.74 3.281,4.74 3.281,4.74 3.521,4.281 false 3.229,3.927 3.396,3.51 3.396,3.51 3.563,3.51 false 4.531,3.073 4.583,2.75 4.583,2.75 4.75,2.75 false 6.76,1.219 7.156,1.573 0.396,0.354 18 false 12 2.885,2.49 3.448,3.021 0.563,0.531 18 false 13 1.823,3.531 2.385,4.063 0.563,0.531 18 false 13 2.802,4.635 3.365,5.167 0.563,0.531 18 false 14 2.646,4.667 3.208,5.198 0.563,0.531 10 false ● 4.979,2.625 5.542,3.156 0.563,0.531 18 false 14 4.823,2.646 5.385,3.177 0.563,0.531 10 false ● 6.177,3.896 6.74,4.427 0.563,0.531 18 false 15 3.542,1.385 4.104,1.917 0.563,0.531 18 false 16 3.646,3.438 4.208,3.969 0.563,0.531 10 false ●*1 3.958,5.188 4.521,5.719 0.563,0.531 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

12 REAR DISC BRAKE PAD SUPPORT PLATE - (Click here) - -
13 REAR DISC BRAKE CYLINDER SLIDE PIN - - - -
14 NO. 1 BUSH DUST BOOT 47775B - - -
15 REAR DISC BRAKE CYLINDER MOUNTING 47822 - - -
16 REAR DISC 42431 (Click here) - -

*1 NO. 1 REAR DISC BRAKE CYLINDER SLIDE BUSH - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear brake removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the brake shoes or pushing back the wheel brake cylinder piston may cause a large clearance between the brake shoes and brake drum. When the brake pedal is depressed with a large clearance between the brake shoes and the brake drum, DTC C13DC00, C13DE00, C140000 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure. (for HV Model)

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)



HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used. (for HV Model)

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

for HV Model: Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.

for HV Model: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model TMC Made)>PRECAUTION

for Gasoline Model: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model TMC Made)>PRECAUTION



Hide 2.REMOVE REAR WHEEL

Hide 4.DISABLE BRAKE CONTROL (for HV Model)

Z101186

Click here(Click here)

Hide 5.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 890C0A 6.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Z101186

Click here(Click here)

Hide 46310B 7.REMOVE PARKING BRAKE ACTUATOR ASSEMBLY

Z101186

Click here(Click here)

Hide 47319F 8.SEPARATE REAR FLEXIBLE HOSE

a.
C445724


Hide 47850 9.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C445725


Hide 04466 10.REMOVE REAR DISC BRAKE PAD

a.
C445726


Hide 04946 11.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

Z101186

Click here(Click here)

Hide 12.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

Z101186

NOTICE:

Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.



a.
C445727


Hide 13.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C445728C02
1.333,0.208 0.677,0.5 true 1.271,1.438 0.677,1.438 true 0.531,0.031 0.813,0.385 0.281,0.354 18 false i 4.438,0.073 4.719,0.427 0.281,0.354 18 false ii 0.479,1.344 0.656,1.552 0.177,0.208 10 true *2 0.479,0.438 0.667,0.656 0.188,0.219 10 true *1
*1 Rear No. 1 Disc Brake Cylinder Slide Pin *2 Rear No. 2 Disc Brake Cylinder Slide Pin


i.

Remove the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin from the rear disc brake cylinder mounting.


ii.

Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from the rear No. 2 disc brake cylinder slide pin.

NOTICE:

Do not damage the rear No. 2 disc brake cylinder slide pin.




Hide 47775B 14.REMOVE NO. 1 BUSH DUST BOOT

a.
C445729


Hide 47822 15.REMOVE REAR DISC BRAKE CYLINDER MOUNTING

a.
C445730


Hide 42431 16.REMOVE REAR DISC

a.
C445731C03
3.667,1.073 4.167,1.083 true 3.667,1.135 3.833,1.135 3.833,1.135 3.833,1.063 true 2.031,0.073 2.406,0.427 0.375,0.354 18 true i, ii 4.198,1 4.51,1.198 0.313,0.198 10 false *a
*a Matchmark - -


i.

Put matchmarks on the rear disc and rear axle hub and bearing assembly.


ii.

Remove the rear disc.