Home › General › MAINTENANCE › REAR DISC BRAKE PAD (for TMMF Made 2WD) › from 2021.07
RM3700E _V1 General _093024 MAINTENANCE _0482442 REAR DISC BRAKE PAD(for TMMF Made 2WD) A

MAINTENANCE  REAR DISC BRAKE PAD(for TMMF Made 2WD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C464308N02
1.688,0.219 2.521,0.385 0.833,0.167 1.646,0.177 2.563,0.427 0.917,0.25 6.531,0.208 6.865,0.208 false 5.552,3.51 5.646,3.146 5.646,3.146 5.813,3.146 false 4.865,1.958 5.219,1.958 false 1.823,4.625 2.521,4.625 false 2.292,1.417 2.635,1.042 2.635,1.042 2.802,1.042 true 1.427,0.292 1.26,0.292 1.26,0.292 0.927,0.802 true 2.083,4.406 2.083,4.625 false 0.99,4.031 1.396,4.031 false 3.104,4.906 3.104,5.25 false 6.51,0.615 6.844,0.615 false 6.313,0.042 6.927,0.375 0.615,0.333 18 false 7 5.865,2.969 6.146,3.323 0.281,0.354 18 false 6 5.5,1.781 5.781,2.135 0.281,0.354 18 false 4 1.615,4.479 1.896,4.833 0.281,0.354 18 false 2 0.792,3.875 1.073,4.229 0.281,0.354 18 false 1 3.146,5.229 3.438,5.542 0.292,0.313 18 false 1 1.76,0.229 2.615,0.438 0.854,0.208 8 false 31.5 (321, 23) 3.104,0.865 3.292,1.156 0.188,0.292 18 true 3 6.302,0.448 6.917,0.781 0.615,0.333 18 false 5 1.5,0.198 1.656,0.396 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR DISC BRAKE ANTI-SQUEAL SHIM 04946 (Click here) - -
2 REAR DISC BRAKE PAD 0466 (Click here) - -
3 REAR DISC BRAKE CYLINDER ASSEMBLY - (Click here) - -
4 NO. 2 PARKING BRAKE WIRE ASSEMBLY 890C0A (Click here) - -
5 INSPECT BRAKE FLUID LEVEL IN RESERVOIR - - (Click here) -
6 REAR WHEEL - - - -
7 NORMAL CONDITION RECOVERY - (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) ● Non-reusable part

CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 04946 1.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM

Z101186

NOTICE:

When replacing worn rear disc brake pads, the rear disc brake anti-squeal shims must be replaced together with the rear disc brake pads.



Hide 04466 2.INSTALL REAR DISC BRAKE PAD

Z101186

CAUTION:
C464310

·

Be careful not to get pinched by the rear disc brake cylinder assembly or other parts when installing the rear disc brake pads.

·

After lifting up the rear disc brake cylinder assembly, secure it in place before performing any work on it.

·

The rear disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.




a.
C466753C01
2.729,0.865 3.083,0.865 true 0.875,0.875 2.542,0.875 true 4.135,0.375 4.49,0.375 true 4.146,1.271 4.5,1.271 true 4.406,1.615 4.76,1.615 true 3.115,0.792 3.427,0.948 0.313,0.156 10 false *b 0.708,0.792 1.021,0.948 0.313,0.156 10 false *a 3.958,0.302 4.271,0.458 0.313,0.156 10 false *b 4.24,1.542 4.552,1.698 0.313,0.156 10 false *c 3.979,1.177 4.292,1.333 0.313,0.156 10 false *a 0.521,0.104 0.771,0.375 0.25,0.271 18 false i
*a Inner Side *b Outer Side
*c Pad Wear Indicator Plate - -


i.

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:

Install the rear disc brake pad so that the rear disc brake pad wear indicator plate is mounted on the upper side of the vehicle.




Hide 47850 3.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C464312N01
1.208,0.781 0.854,1.365 true 0.375,0 0.927,0.354 0.552,0.354 18 false i 3.927,0 4.479,0.354 0.552,0.354 18 false ii 0.635,1.396 1.083,1.604 0.448,0.208 10 false SST

i.

Using SST, push back the front disc brake piston.

SST
09719-77020  

NOTICE:
·

Make sure the brake fluid does not overflow from the reservoir.

·

Do not forcibly push in the rear disc brake piston.




ii.

Hold the rear disc brake cylinder slide pin (lower side) and install the rear disc brake cylinder assembly to the front disc brake cylinder mounting with a new bolt.

Torque:
31.5 N*m (321 kgf*cm, 23 ft.*lbf)



Hide 890C0A 4.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Z101186

Click here(Click here)

Hide 6.INSTALL REAR WHEEL