Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2021.07
RM3700E _59 Vehicle Exterior _092999 WIPER / WASHER _0438366 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B127987  Humidity/Rain Sensor Missing Message  


DESCRIPTION

The main body ECU (multiplex network body ECU) and rain sensor communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B127987 Humidity/Rain Sensor Missing Message
Detection Condition:

Auxiliary battery voltage is 9.5 V or more


Malfunction Status:

Communication malfunction with rain sensor


Malfunction Duration:

10 seconds or more


·

Rain sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)


○ Main Body A

WIRING DIAGRAM

E469977E01
1.323,3.01 1.635,3.208 0.313,0.198 10 false H5 1.292,1.917 1.604,2.115 0.313,0.198 10 false MB 1.323,1.708 1.635,1.906 0.313,0.198 10 false 27 1.313,2.792 1.625,2.99 0.313,0.198 10 false 11 4.802,1.688 5.115,1.885 0.313,0.198 10 false 38 6.021,3.427 6.333,3.625 0.313,0.198 10 false V9 6.021,3.615 7.021,3.948 1,0.333 10 false Rain Sensor 1.917,2.375 4.042,2.615 2.125,0.24 10 false Power Distribution Box Assembly 1.813,1.167 3.25,1.542 1.438,0.375 10 false ECU-IGR NO. 2 3.083,0.948 4.521,1.323 1.438,0.375 10 false from IGR-NO. 2 Relay 0.094,3.5 1.76,4.042 1.667,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 0.583,4.365 2.708,4.604 2.125,0.24 10 false : LIN Communication Line 0.865,3.021 1.385,3.25 0.521,0.229 10 false LIN4 4.802,1.896 5.115,2.094 0.313,0.198 10 false 4B 6.01,2.375 6.323,2.573 0.313,0.198 10 false ES 6,3 6.354,3.24 0.354,0.24 10 false MPX 6,1.885 6.354,2.125 0.354,0.24 10 false SIG 5.792,1.792 6.146,2.031 0.354,0.24 10 false 4 5.792,2.271 6.146,2.51 0.354,0.24 10 false 2 5.802,2.833 6.156,3.073 0.354,0.24 10 false 3 0.906,1.917 1.219,2.115 0.313,0.198 10 false IGR

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1

*1: w/ Entry and Start System




PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - RAIN SENSOR)

Pre-procedure1

a.

Disconnect the H5 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the V9 rain sensor connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H5,V9)Location & Routing

Click Connector(H5)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECU

Click Connector(V9)Body>No. 1 Roof Wire>Rain Sensor

H5-11 (LIN4) - V9-3 (MPX) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.
E366392C45
1.5,0.25 1.917,0.5 0.417,0.25 1.698,1.125 1.948,1.792 1.948,1.792 2.115,1.792 true 1.615,0.292 2.021,0.531 0.406,0.24 10 false H5 2.229,1.708 2.583,1.927 0.354,0.219 10 false LIN4 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a
*a Component without harness connected
(Main Body ECU (Multiplex Network Body ECU))


Check for voltage and pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H5)Location & Routing

Click Connector(H5)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECU

H5-11 (LIN4) - Body ground Ignition switch ON Pulse generation



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - RAIN SENSOR)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - RAIN SENSOR)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(V9)Location & Routing

Click Connector(V9)Body>No. 1 Roof Wire>Rain Sensor

V9-4 (SIG) - Body ground Ignition switch off Below 1 V
V9-4 (SIG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - RAIN SENSOR)
4.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V9)Location & Routing

Click Connector(V9)Body>No. 1 Roof Wire>Rain Sensor

V9-2 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - RAIN SENSOR)

Pre-procedure1

a.

Disconnect the 4B power distribution box assembly connector.


b.

Disconnect the V9 rain sensor connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V9)Location & Routing

Click Connector(V9)Body>No. 1 Roof Wire>Rain Sensor

4B-38 - V9-4 (SIG) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR