Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for LHD) › from 2021.07
RM3700E _57 Power Source / Network _093028 POWER DISTRIBUTION _0483098 MAIN BODY ECU(for LHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E466649N01
4.917,1.083 7,3.333 2.083,2.25 6.531,0.208 6.865,0.208 false 5.417,2.458 5.417,2.792 false 6.5,0.594 6.833,0.594 false 2.792,3.958 3.125,3.958 false 2.5,2.667 2.667,2.667 2.667,2.667 2.927,2.76 false 3.667,1.875 4,1.875 false 6.521,2.542 6.521,2.792 false 5.958,3.333 5.958,3.667 false 6.365,0.063 6.646,0.417 0.281,0.354 18 false 1 6.323,0.448 6.604,0.802 0.281,0.354 18 false 2 3.198,3.813 3.479,4.167 0.281,0.354 18 false 3 2.302,2.531 2.583,2.885 0.281,0.354 18 false 4 5.979,3.719 6.26,4.073 0.281,0.354 18 false 5 3.479,1.74 3.76,2.094 0.281,0.354 18 false 6 6.427,2.833 6.708,3.188 0.281,0.354 18 false 7 5.365,2.833 5.677,3.031 0.313,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY 55480D - - -
4 NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY 55308B - - -
5 POWER DISTRIBUTION BOX ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU - (Click here) - -
6 WIRING HARNESS CLAMP BRACKET 82715 - - -
7 MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 89221 (Click here) - -

*1 POWER DISTRIBUTION BOX ASSEMBLY - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the main body ECU (multiplex network body ECU) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
for HV Model:
Main body ECU (multiplex network body ECU)
Code registration
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, HV model)

·

Entry and start system (for Start function, HV model)

·

Hybrid control system cannot be started


See Service Bulletin for the registration method.
for Gasoline Model:
Main body ECU (multiplex network body ECU)
Code registration
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, Gasoline model)

·

Entry and start system (for Start function, Gasoline model)

·

Engine start function


See Service Bulletin for the registration method.

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55480D 3.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 55308B 4.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.
E466650


Hide 5.REMOVE POWER DISTRIBUTION BOX ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU

a.
E466651C01
6.188,0.458 6.073,0.688 false 6.427,1.177 6.198,1.104 true 1.052,2.469 0.938,2.698 false 1.292,3.167 1.063,3.094 true 1.104,0.323 1.302,0.646 0.198,0.323 18 true i 2.458,0.802 2.698,1.125 0.24,0.323 18 true ii 4.01,0.073 4.25,0.396 0.24,0.323 18 true iii 4.646,0.896 4.938,1.219 0.292,0.323 18 true iv 0.344,2.042 0.583,2.354 0.24,0.313 18 true v 4.323,2.063 4.563,2.375 0.24,0.313 18 true vi 6,0.719 6.313,0.917 0.313,0.198 10 false *a 6.021,1 6.333,1.198 0.313,0.198 10 false *a 0.865,2.719 1.177,2.917 0.313,0.198 10 false *a 0.896,2.99 1.208,3.188 0.313,0.198 10 false *a 0.49,2.125 0.76,2.375 0.271,0.25 12 true *A
*A for HV Model - -
*a Lock Lever - -


i.

Disconnect the 5 connectors.


ii.

Disengage the clamp.


iii.

Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.


iv.

Disengage the clamp.


v.

for HV Model:

1.

Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.



vi.

Disconnect the 5 connectors.



b.
E466652C01
6.021,2.677 6.104,2.469 false 6.167,3.125 6.365,3.177 true 4.51,0.083 4.698,0.375 0.188,0.292 18 true i 2.594,0.229 2.823,0.5 0.229,0.271 18 true ii 1.156,1.969 1.385,2.24 0.229,0.271 18 false iii 3.958,2.031 4.854,2.365 0.896,0.333 18 true iv, v, vi 3.521,0.031 3.708,0.323 0.188,0.292 18 true i 5.948,2.708 6.26,2.906 0.313,0.198 10 false *a 5.99,3.021 6.302,3.219 0.313,0.198 10 false *a
*a Lock Lever - -


i.

Remove the 2 nuts.


ii.

Using a screwdriver with its tip wrapped in protective tape, disengage the claws to pull out the power distribution box assembly with multiplex network body ECU.


iii.

Disengage the claws.


iv.

Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.


v.

Disconnect the connector.


vi.

Remove the power distribution box assembly with multiplex network body ECU.



Hide 82715 6.REMOVE WIRING HARNESS CLAMP BRACKET

a.
E466653


Hide 89221 7.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

a.
E448344C01
0.604,1.052 0.99,1.052 true 1.104,1.115 1.323,1.344 true 0.417,0.99 0.729,1.188 0.313,0.198 10 false *2 1.385,1.271 1.698,1.469 0.313,0.198 10 false *1 1.75,0.167 2,0.531 0.25,0.365 18 false i 6.469,1.406 6.667,1.708 0.198,0.302 18 false ii 2.469,2.323 2.719,2.688 0.25,0.365 18 false iv 5.521,0.073 5.792,0.333 0.271,0.26 18 false iii
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)
V100135

Push
V100136

Insert
V100137

Raise
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2) - -


i.

Press the claw of the power distribution box assembly as shown in the illustration to release the lock.


ii.

With the power distribution box assembly lock released, insert a screwdriver with its tip wrapped in protective tape horizontally between the main body ECU (multiplex network body ECU) and the power distribution box assembly.

NOTICE:
·

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).

·

Do not insert the screwdriver under the connector socket of the main body ECU (multiplex network body ECU).




iii.

Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.

NOTICE:

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).



iv.

Remove the main body ECU (multiplex network body ECU) as shown in the illustration.

NOTICE:

Do not touch the main body ECU (multiplex network body ECU) connector.