Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2021.07
RM3700E _59 Vehicle Exterior _092999 WIPER / WASHER _0438366 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B276C88  Alarm / Wiper LIN Bus off  


DESCRIPTION

The main body ECU (multiplex network body ECU) and rain sensor communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B276C88 Alarm / Wiper LIN Bus off
Detection condition:

Auxiliary battery voltage is 9.5 V or more


Malfunction Status:

A malfunction in the communication or LIN communication line between the main body ECU (multiplex network body ECU) and components of the wiper system occurs


Malfunction Time:

7 seconds or more


·

Rain sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)


○ Main Body A

WIRING DIAGRAM

E430037E08
0.604,2.385 2.563,2.688 1.958,0.302 10 false : LIN Communication Line 1.875,1.844 2.813,2.146 0.938,0.302 10 false Rain Sensor 1.865,1.646 2.177,1.844 0.313,0.198 10 false V9 2.344,1.01 2.802,1.25 0.458,0.24 10 false MPX 2.75,0.854 2.958,1.115 0.208,0.26 10 false 3 4.229,0.844 4.531,1.104 0.302,0.26 10 false 11 4.521,1.031 4.927,1.313 0.406,0.281 10 false LIN4 4.146,1.802 5.802,2.427 1.656,0.625 10 false Main Body ECU (Multiplex Network Body ECU) 4.156,1.635 4.448,1.854 0.292,0.219 10 false H5

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449
Result:
Proceed to
NEXT




NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC

Pre-procedure1

a.

Disconnect the V9 rain sensor connector.


Procedure1

a.

Read the DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449
Result:
Result Proceed to
B276C88 is output A
B127987 is output B
None of the above conditions are met C



Post-procedure1

a.

None



A

3.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

B

C

3.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

Pre-procedure1

a.

Disconnect the H5 main body ECU (multiplex network body ECU) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V9,H5)Location & Routing

V9-3 (MPX) - H5-11 (LIN4) Always Below 1 Ω
V9-3 (MPX) or H5-11 (LIN4) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR