Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › from 2021.07
RM3700E _57 Power Source / Network _093026 NETWORKING _0445205 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Communication stop for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Brake actuator assembly branch line or connector

·

Power source circuit of brake actuator assembly

·

Brake actuator assembly ground circuit

·

Brake actuator assembly



WIRING DIAGRAM

for TMC Made


C440234E02
0.063,2.063 3.885,2.26 3.823,0.198 10 false No. 2 Global CAN Junction Connector 0.083,1.896 0.698,2.094 0.615,0.198 10 false H112 1.625,0.823 1.781,1.021 0.156,0.198 10 false 3 1.615,1.365 1.771,1.563 0.156,0.198 10 false 9 5.51,0.823 5.906,1.135 0.396,0.313 10 false 27 5.521,1.365 5.917,1.677 0.396,0.313 10 false 43 5.781,0.906 6.396,1.104 0.615,0.198 10 false CANH 5.792,1.458 6.406,1.656 0.615,0.198 10 false CANL 2.156,2.875 5.979,3.073 3.823,0.198 10 false from IGR-NO. 1 Relay 2.198,3.479 6.021,3.677 3.823,0.198 10 false from Auxiliary Battery 2.198,4.073 6.021,4.271 3.823,0.198 10 false from Auxiliary Battery 4.333,3.083 5.406,3.26 1.073,0.177 10 false ECU-IGR NO. 3 4.49,3.677 5.458,3.854 0.969,0.177 10 false ABS NO. 1 4.5,4.292 5.469,4.469 0.969,0.177 10 false ABS NO. 2 5.323,5.75 6.292,5.927 0.969,0.177 10 false A94 5.313,5.896 7.135,6.313 1.823,0.417 10 false Brake Actuator Assembly 5.521,2.781 5.917,3.094 0.396,0.313 10 false 45 5.531,3.375 5.927,3.688 0.396,0.313 10 false 46 5.531,4 5.927,4.313 0.396,0.313 10 false 14 5.604,4.531 6,4.844 0.396,0.313 10 false 1 5.542,5.073 5.938,5.385 0.396,0.313 10 false 30 5.802,2.885 6.198,3.198 0.396,0.313 10 false IGR 5.792,3.49 6.188,3.802 0.396,0.313 10 false BM 5.792,4.094 6.188,4.406 0.396,0.313 10 false +BS 5.792,4.646 6.188,4.958 0.396,0.313 10 false GND1 5.792,5.156 6.188,5.469 0.396,0.313 10 false GND2


for TMMF Made


C440233E02
5.292,5.719 5.75,5.917 0.458,0.198 10 false A39 5.792,0.604 6.25,0.802 0.458,0.198 10 false CANH 5.792,1.135 6.25,1.333 0.458,0.198 10 false CANL 5.792,2.5 6.25,2.698 0.458,0.198 10 false IGR 5.792,5.156 6.25,5.354 0.458,0.198 10 false GND2 5.563,0.51 6.021,0.708 0.458,0.198 10 false 5 5.51,1.042 5.969,1.24 0.458,0.198 10 false 19 5.5,4.01 5.958,4.208 0.458,0.198 10 false 30 5.521,4.542 5.979,4.74 0.458,0.198 10 false 46 1.625,0.51 2.083,0.708 0.458,0.198 10 false 3 1.625,1.052 2.083,1.25 0.458,0.198 10 false 9 0.073,1.542 0.531,1.74 0.458,0.198 10 false H112 0.063,1.708 2.781,1.958 2.719,0.25 10 false No. 2 Global CAN Junction Connector 4.521,3.719 5.719,3.938 1.198,0.219 10 false ABS NO. 1 5.292,5.885 7.156,6.302 1.865,0.417 10 false Brake Actuator Assembly 5.802,3.573 6.26,3.771 0.458,0.198 10 false +BM 2.177,4.083 4.25,4.427 2.073,0.344 10 false from Auxiliary Battery 5.583,3.458 6.042,3.656 0.458,0.198 10 false 1 5.792,4.625 6.25,4.823 0.458,0.198 10 false GND1 5.51,5.063 5.969,5.26 0.458,0.198 10 false 14 2.167,3.542 3.865,3.854 1.698,0.313 10 false from Auxiliary Battery 4.521,4.26 5.719,4.479 1.198,0.219 10 false ABS NO. 2 1.365,2.5 4.521,2.76 3.156,0.26 10 false from Engine Stop and Start ECU*1 2.021,3.031 3.604,3.323 1.583,0.292 10 false from IGR-NO. 1 Relay*2 5.792,4.094 6.25,4.292 0.458,0.198 10 false +BS 5.51,2.396 5.969,2.594 0.458,0.198 10 false 36 4.344,3.188 5.542,3.406 1.198,0.219 10 false ECU-IGR NO. 3 4.563,2.635 4.875,2.833 0.313,0.198 10 false *1 5.302,2.771 5.615,2.969 0.313,0.198 10 false *2 0.25,5.781 3.406,6.042 3.156,0.26 10 false *1: w/ Stop and Start System 0.25,6.26 3.406,6.521 3.156,0.26 10 false *2: w/o Stop and Start System


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for TMC Made A
for TMMF Made B



A

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)

B

4.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)
2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A94 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A94)Location & Routing

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A94-27 (CANH) - A94-43 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A94)Location & Routing

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A94-1 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A94-30 (GND2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A94)Location & Routing

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A94-46 (BM) - Body ground Ignition switch off 11 to 14 V
A94-14 (+BS) - Body ground Ignition switch off 11 to 14 V
A94-45 (IGR) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

GO TO STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

4.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A39 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A39)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A39-5 (CANH) - A39-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY)

5.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

8.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
6.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A39)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A39-46 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A39-14 (GND2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A39)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A39-1 (+BM) - Body ground Ignition switch off 11 to 14 V
A39-30 (+BS) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A39)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A39-36 (IGR) - Body ground Ignition switch ON 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

NG

GO TO STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A39)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A39-46 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A39-14 (GND2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A39)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A39-1 (+BM) - Body ground Ignition switch off 11 to 14 V
A39-30 (+BS) - Body ground Ignition switch off 11 to 14 V
A39-36 (IGR) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)