Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for Gasoline Model TMMF Made RHD) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0480783 BRAKE ACTUATOR(for Gasoline Model TMMF Made RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for Gasoline Model TMMF Made RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C463475N01
4.948,0.5 5.281,0.5 false 4.906,1.469 5.24,1.469 false 2.896,0.531 3.229,0.531 false 6.417,0.271 6.729,0.271 false 6.417,0.833 6.688,0.833 false 6.417,1.333 6.729,1.333 false 4.531,2.083 4.865,2.083 false 2.729,3.75 3.063,3.75 false 1.031,2.917 1.365,2.917 false 2.188,5.167 2.521,5.167 false 1.115,4.802 1.448,4.802 false 1.073,3.781 1.406,3.781 false 5.323,0.365 5.604,0.719 0.281,0.354 18 false 3 5.292,1.354 5.573,1.708 0.281,0.354 18 false 5 2.698,0.385 2.979,0.74 0.281,0.354 18 false 4 6.198,0.135 6.729,0.573 0.531,0.438 18 false 1 6.198,0.688 6.729,1.125 0.531,0.438 18 false 2 6.198,1.177 6.448,1.615 0.25,0.438 18 false 7 4.917,1.948 5.167,2.385 0.25,0.438 18 false 6 2.385,0.49 2.75,0.76 0.365,0.271 10 false x12 3.125,3.583 3.458,4 0.333,0.417 18 false 8 1.406,2.76 1.74,3.177 0.333,0.417 18 false 9 1.417,3.615 1.75,4.031 0.333,0.417 18 false 10 2.792,4.25 3.156,4.521 0.365,0.271 10 false x3 1.854,4.99 2.188,5.406 0.333,0.417 18 false 12 1.479,4.635 1.813,5.052 0.333,0.417 18 false 11

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 REMOVE WINDSHIELD WIPER MOTOR AND LINK - - - -
4 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
5 WATER GUARD PLATE LH 55735A - - -
6 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
7 DRAIN BRAKE FLUID - - (Click here) -
8 ECM 89661 - - -
9 AIR CLEANER CAP WITH AIR CLEANER HOSE - - - -
10 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 17801 - - -
11 AIR CLEANER CASE SUB-ASSEMBLY 17701 - - -
12 BATTERY CLAMP SUB-ASSEMBLY 74404A - - -

C460873N01
4,0.25 4.583,1.583 0.583,1.333 2.583,0.667 3.333,1.5 0.75,0.833 3.854,1.75 4.5,1.75 false 4.583,0.75 5.167,0.75 false 2.198,1.25 2.583,1.25 false 1.042,2.135 1.427,2.135 false 4.844,1.615 5.24,1.917 0.396,0.302 18 false 15 5.531,0.615 5.906,0.906 0.375,0.292 18 false 14 1.833,1.094 2.208,1.385 0.375,0.292 18 false 14 2.969,2.083 3.344,2.375 0.375,0.292 10 false x2 0.708,1.99 1.083,2.281 0.375,0.292 18 false 13

Procedure Part Name Code
Z101186

Z101188

Z101187

13 ENGINE ROOM MAIN WIRE - (Click here) - -
14 BRAKE LINE - (Click here) - -
15 BRAKE ACTUATOR WITH BRACKET - (Click here) - -

C442406N03
3.042,1.542 3.333,1.542 false 3.125,2.844 3.417,2.844 false 3.292,3.573 3.479,3.573 3.479,3.573 3.625,3.875 false 2.552,4.271 2.844,4.271 false 2.604,4.625 2.896,4.625 false 2.677,1.385 3.229,1.74 0.552,0.354 18 false 17 2.927,2.76 3.177,3.031 0.25,0.271 10 false *1 2.948,3.406 3.333,3.719 0.385,0.313 18 false 16 2.219,4.094 2.604,4.406 0.385,0.313 18 false 19 2.25,4.479 2.635,4.792 0.385,0.313 18 false 20 3.042,4.26 3.292,4.438 0.25,0.177 10 false x3 3.031,4.604 3.281,4.781 0.25,0.177 10 false x3 3,4.927 3.25,5.104 0.25,0.177 10 false x3 4.094,4.969 4.344,5.146 0.25,0.177 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

16 NO. 1 BRAKE ACTUATOR BRACKET 44591 (Click here) - -
17 BRAKE ACTUATOR ASSEMBLY 44510 (Click here) - -
18 NO. 1 BRAKE ACTUATOR CASE COLLAR 44521A - - -
19 BRAKE ACTUATOR BRACKET CUSHION 44547B - - -

*1 BRAKE ACTUATOR BRACKET ASSEMBLY - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Skid control ECU (brake actuator assembly) Operate the electric parking brake switch (electric parking brake switch assembly) Parking brake indicator light (red) blinks when the ignition switch is first turned ON (Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55815E 4.REMOVE FRONT NO. 1 VENTILATOR SEAL

Hide 55701J 6.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 7.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 9.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 10.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 11.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 12.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 13.DISCONNECT ENGINE ROOM MAIN WIRE

a.
C460874C01
2.135,0.021 2.417,0.375 0.281,0.354 18 false i
V113147

Release the lock lever
V113148

Disconnect the connector


i.

Release the lock lever and disconnect the connector from the brake actuator assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.




Hide 14.SEPARATE BRAKE LINE

a.
C460875C01
2.073,2.854 2.469,2.99 true 1.458,3.177 1.76,2.969 true 1.26,2.792 1.594,2.792 true 1.26,2.438 1.729,2.708 true 1.906,2.688 2.229,2.344 true 2.042,2.677 2.375,2.677 true 2.542,2.938 2.844,3.167 0.302,0.229 10 true *a 1.198,3.219 1.406,3.438 0.208,0.219 10 true *b 1.01,2.688 1.208,2.875 0.198,0.188 10 true *c 1,2.323 1.208,2.51 0.208,0.188 10 true *d 2.281,2.219 2.479,2.417 0.198,0.198 10 true *e 2.427,2.583 2.635,2.771 0.208,0.188 10 true *f 2.063,0.063 2.344,0.344 0.281,0.281 18 false i 0.417,1.958 0.698,2.24 0.281,0.281 18 true ii 3.979,1.969 4.26,2.25 0.281,0.281 18 true iii
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly *b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH *d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH *f To Front Wheel Cylinder Assembly RH


i.

Using a 10 mm union nut wrench, disconnect the brake line from the front flexible hose.


ii.

Use tags or make a memo to identify the places to reconnect the brake lines.


iii.

Using a 10 mm and 12 mm union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.



Hide 15.REMOVE BRAKE ACTUATOR WITH BRACKET

Z101186

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Remove the brake actuator with bracket while avoiding the brake lines.



a.
C460876


Hide 44591 16.REMOVE NO. 1 BRAKE ACTUATOR BRACKET

Z101186

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C429858


Hide 44510 17.REMOVE BRAKE ACTUATOR ASSEMBLY

Z101186

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C442409


Hide 44521A 18.REMOVE NO. 1 BRAKE ACTUATOR CASE COLLAR

a.
C442410


Hide 44547B 19.REMOVE BRAKE ACTUATOR BRACKET CUSHION

a.
C442411