Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for LHD) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0480782 BRAKE ACTUATOR(for LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C460859N01
2.635,0.583 2.969,0.583 false 3.333,0.938 3.667,0.938 false 5.302,2 5.635,2 false 4.563,3.375 4.896,3.375 false 6.396,1.104 6.729,1.104 false 6.375,0.771 6.708,0.771 false 6.406,0.313 6.74,0.313 false 5.865,0.146 6.531,0.479 0.667,0.333 18 false 1, 2 6.156,0.594 6.49,1.01 0.333,0.417 18 false 3 6.177,0.948 6.51,1.365 0.333,0.417 18 false 8 5.74,1.844 6.073,2.26 0.333,0.417 18 false 4 3.792,0.802 4.125,1.219 0.333,0.417 18 false 5 3.073,0.417 3.406,0.833 0.333,0.417 18 false 6 4.99,3.208 5.323,3.625 0.333,0.417 18 false 7 2.313,1.365 2.771,1.563 0.458,0.198 10 false x11

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY - - - -
5 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
6 WATER GUARD PLATE RH 55734A - - -
7 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
8 DRAIN BRAKE FLUID - - (Click here) -

C460860N01
2.344,0.26 2.51,0.26 2.51,0.26 2.781,0.646 false 2.448,2.271 2.615,2.271 2.615,2.271 3,1.583 false 3.875,1.448 4.042,1.448 4.042,1.448 4.198,1.656 false 3.906,0.438 4.073,0.438 4.073,0.438 4.229,0.646 false 2.146,0.083 2.427,0.438 0.281,0.354 18 false 9 2.104,2.073 2.552,2.427 0.448,0.354 18 false 10 3.781,0.333 3.938,0.531 0.156,0.198 10 false ● 3.75,1.333 3.906,1.531 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

9 SUCTION TUBE SUB-ASSEMBLY B 88707B (Click here) - -
10 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY 88710E (Click here) - -

● Non-reusable part - -

C460861N01
2.594,2.542 2.844,2.542 false 4.469,1.615 4.698,2.104 4.698,2.104 4.865,2.104 false 5.25,1.656 5.25,1.323 5.25,1.323 5.417,1.323 false 5.104,1.656 5.104,1.323 5.104,1.323 5.271,1.323 false 4.198,0.552 4.198,0.219 4.198,0.219 4.781,0.219 false 4.26,0.219 4.26,0.521 false 4.333,0.219 4.333,0.49 false 4.406,0.229 4.406,0.479 false 2.313,2.375 2.865,2.729 0.552,0.354 18 false 11 5.75,1.177 6.302,1.531 0.552,0.354 18 false 12 5.125,1.948 5.677,2.302 0.552,0.354 18 false 13 4.885,2.615 5.198,2.813 0.313,0.198 10 false x2 5.021,0.104 5.573,0.458 0.552,0.354 18 false 12

Procedure Part Name Code
Z101186

Z101188

Z101187

11 ENGINE ROOM MAIN WIRE - (Click here) - -
12 SEPARATE BRAKE LINE - (Click here) - -
13 BRAKE ACTUATOR WITH BRACKET - (Click here) - -

C460862N01
4.063,0.729 4.313,0.729 false 4.135,3.219 4.385,3.219 false 4.052,2.135 4.292,1.719 4.292,1.719 4.458,1.719 false 4.927,4.135 5.26,4.135 false 4.927,4.625 5.26,4.625 false 3.927,4.281 4.26,4.281 false 3.927,4.75 4.26,4.75 false 2.969,4.531 3.302,4.531 false 3.021,4.938 3.354,4.938 false 4.563,0.625 5.115,0.979 0.552,0.354 18 false 15 4.635,3.115 5.188,3.469 0.552,0.354 18 false 14 5.313,3.969 5.865,4.323 0.552,0.354 18 false 17 5.313,4.479 5.865,4.833 0.552,0.354 18 false 16 3.604,4.604 4.156,4.958 0.552,0.354 18 false 16 3.615,4.104 4.167,4.458 0.552,0.354 18 false 17 2.677,4.354 3.229,4.708 0.552,0.354 18 false 17 2.708,4.771 3.26,5.125 0.552,0.354 18 false 16 4.542,1.594 4.854,1.792 0.313,0.198 10 false *1 4.875,2.302 5.188,2.5 0.313,0.198 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

14 NO. 1 BRAKE ACTUATOR BRACKET 44591 (Click here) - -
15 BRAKE ACTUATOR ASSEMBLY 44510 (Click here) - -
16 NO. 1 BRAKE ACTUATOR CASE COLLAR 44521A - - -
17 BRAKE ACTUATOR BRACKET CUSHION 44547B - - -

*1 BRAKE ACTUATOR BRACKET ASSEMBLY - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Skid control ECU (brake actuator assembly) for HV Model:
1.

Bleed air

2.

Perform "Reset Memory"

3.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)
Operate the electric parking brake switch (electric parking brake switch assembly) Parking brake indicator light (red) blinks when the ignition switch is first turned to ON for HV Model:
(Click here)
for Gasoline Model:
(Click here)

NOTICE:

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed. Therefore, when servicing the brake system components, do not operate the brake pedal while the auxiliary battery is connected.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55815E 5.REMOVE FRONT NO. 1 VENTILATOR SEAL

Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 8.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 88707B 9.REMOVE SUCTION TUBE SUB-ASSEMBLY B

a.
C460850C01
0.063,0.042 0.5,0.354 0.438,0.313 18 true i, ii 3.104,0.031 3.573,0.375 0.469,0.344 18 false iii 4.406,0.042 4.729,0.323 0.323,0.281 18 true iv
V113147

Rotate in this Direction - -


i.

Remove the bolt and rotate the hook connector as shown in the illustration.


ii.

Disconnect the suction tube sub-assembly B from the air conditioning unit assembly.


iii.

Remove the O-ring from the suction tube sub-assembly B.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



iv.

Disengage the clamp to separate the suction tube sub-assembly B.



Hide 88710E 10.REMOVE AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.
C460851C02
0.063,0.063 0.24,0.406 0.177,0.344 18 true i 4.406,0.052 4.677,0.344 0.271,0.292 18 true iii 3.135,0.042 3.458,0.396 0.323,0.354 18 false ii
V113147

Remove in this Direction - -


i.

Disconnect the air conditioning tube and accessory assembly from the air conditioning unit assembly.


ii.

Remove the O-ring from the air conditioning tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



iii.

Disengage the clamp to separate the air conditioning tube and accessory assembly.



Hide 11.DISCONNECT ENGINE ROOM MAIN WIRE

a.
C460852C01
1.854,0.052 2.135,0.406 0.281,0.354 18 false i
V113147

Release the lock lever
V113148

Disconnect the connector


i.

Release the lock lever and disconnect the connector from the brake actuator assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.




Hide 12. SEPARATE BRAKE LINE

a.
C460853C01
1.583,1.146 1.844,1.5 true 1.281,1.01 0.833,1.25 true 1.458,0.729 0.833,0.583 true 1.375,0.885 0.833,0.833 true 1.552,0.594 0.833,0.25 true 2.333,0.708 1.802,0.823 true 2.396,0.604 2.604,0.823 0.208,0.219 10 true *a 1.813,1.51 2.021,1.698 0.208,0.188 10 true *b 0.594,0.125 0.802,0.344 0.208,0.219 10 true *c 0.625,0.448 0.802,0.656 0.177,0.208 10 true *d 0.625,0.719 0.813,0.938 0.188,0.219 10 true *e 0.677,1.271 0.833,1.469 0.156,0.198 10 true *f 0.344,0.063 0.625,0.417 0.281,0.354 18 false i 3.969,0.073 4.25,0.427 0.281,0.354 18 false ii
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly *b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH *d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH *f To Front Wheel Cylinder Assembly RH


i.

Use tags or make a memo to identify the places to reconnect the brake lines.


ii.

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.



Hide 13.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C460854C01
0.385,0.271 0.667,0.625 0.281,0.354 18 false i 2.448,0.083 2.667,0.406 0.219,0.323 18 true ii 5.104,0.271 5.385,0.625 0.281,0.354 18 false iii
V113147

Move in this Direction - -


i.

Move aside the suction pipe sub-assembly and air conditioner tube and accessory assembly as shown in the illustration.

NOTICE:

Do not apply excessive force to the suction pipe sub-assembly and air conditioner tube and accessory assembly.



ii.

Remove the 2 nuts.


iii.

Remove the bolt and brake actuator with bracket from the vehicle body.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Remove the brake actuator with bracket while avoiding the brake lines.




Hide 44591 14.REMOVE NO. 1 BRAKE ACTUATOR BRACKET

Z101186

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C460855


Hide 44510 15.REMOVE BRAKE ACTUATOR ASSEMBLY

Z101186

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C460856


Hide 44521A 16.REMOVE NO. 1 BRAKE ACTUATOR CASE COLLAR

a.
C460857


Hide 44547B 17.REMOVE BRAKE ACTUATOR BRACKET CUSHION

a.
C460858