|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
for HFC-134a(R134a):
Compressor oil ND-OIL 8 or equivalent for HFO-1234yf(R1234yf): Compressor oil ND-OIL 12 or equivalent |
- | - |
1.ADJUST COMPRESSOR OIL
| *a | VST Valve (Valve Inside Suction Port) | *b | Suction Port |
| *c | Down | *d | Up |
| *e | Pulley | - | - |
When replacing the compressor with pulley assembly with a new one, gradually discharge the inert gas (helium) from the service valve, and drain the following amount of oil before installation.
If a new compressor with pulley assembly is installed without removing the same amount of compressor oil as is remaining in the pipes, the amount of compressor oil will be excessive. This prevents heat exchange in the refrigerant cycle and will cause the air conditioning system to malfunction.
A certain amount of compressor oil remains in the compressor with pulley assembly during circulation and the compressor may be damaged if the amount of compressor oil is more/less than this amount. Therefore, make sure to adjust the amount of compressor oil correctly.
If the amount of compressor oil remaining in the removed compressor with pulley assembly is excessively low, check for compressor oil leaks.
Do not race the engine before replacing the compressor with pulley assembly.
Make sure to use ND-OIL 8 or equivalent compressor oil. (for HFC-134a(R134a))
Make sure to use ND-OIL 12 or equivalent compressor oil. (for (fir HFO-1234yf(R1234yf))
1. Remove the suction seal cap.
2. Using a screwdriver with its tip wrapped in protective tape, insert the screwdriver through the suction port and set the VST valve (valve inside suction port) to the open position.
Be sure not to damage the piping contact surfaces with the tip of the screwdriver.
3. Lightly shake the compressor with pulley assembly with the suction port facing down, and drain the oil (*1).
Do not allow the pulley to come into contact with the compressor oil.
4. With the pulley facing down, rotate the pulley in the direction shown by the arrow 10 times at a rate of approximately once every 2 seconds (*2).
If the pulley is rotated, refrigerant or oil might splash out. Thus, keep your face away from the suction port.
5. Rotate the pulley once in the direction shown by the arrow while quickly turning the compressor with pulley assembly so the pulley is up (*3).
6. Proceed with the above procedure (*1) and drain the oil (*4).
7. Drain the oil by repeating the procedures above approximately 5 times (from (*2) to (*4)).
| Standard (Amount of Oil to be Removed) | Amount of Oil Inside a New Compressor Assembly with Pulley |
|---|---|
| 30 cm3 | 60 cm3 |
If too much oil has been removed, set the VST valve to the open position through the suction port, and add oil.
88310
2.INSTALL COMPRESSOR WITH PULLEY ASSEMBLY
Temporarily install the compressor with pulley assembly with the 4 bolts.
Tighten the 4 bolts and install the compressor with pulley assembly in the order shown in the illustration.
Connect the connector.
88711
3.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with pulley assembly.
for HFC-134a(R134a):
ND-OIL 8 or equivalent
for HFO-1234yf(R1234yf):
ND-OIL 12 or equivalent
Install the O-ring to the No. 1 cooler refrigerant discharge hose.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the No. 1 cooler refrigerant discharge hose to the compressor with pulley assembly with the bolt.
88704
4.CONNECT SUCTION HOSE SUB-ASSEMBLY
Remove the vinyl tape from the suction hose sub-assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with pulley assembly.
for HFC-134a(R134a):
ND-OIL 8 or equivalent
for HFO-1234yf(R1234yf):
ND-OIL 12 or equivalent
Install the O-ring to the suction hose sub-assembly.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the suction hose sub-assembly to the compressor with pulley assembly with the bolt.
16361A
5.INSTALL FAN AND GENERATOR V BELT
51410
6.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
7.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
8. WARM UP ENGINE
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
9.INSPECT FOR REFRIGERANT LEAK
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT