Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT EVAPORATOR TEMPERATURE SENSOR › from 2021.07
RM3700E _58 Vehicle Interior _093020 HEATING / AIR CONDITIONING _0438498 FRONT EVAPORATOR TEMPERATURE SENSOR A

HEATING / AIR CONDITIONING  FRONT EVAPORATOR TEMPERATURE SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
I117548N01
0.99,3.125 0.99,2.792 false 5.094,1.156 5.094,0.823 false 3.333,3.615 3.333,3.281 false 5.156,4.156 5.49,4.156 false 5.49,3.177 5.49,2.844 false 2.281,3 2.281,2.667 false 4.271,1.583 4.604,1.583 false 6.406,1.833 6.74,1.833 false 5.844,0.875 6.052,0.583 6.052,0.583 6.219,0.583 false 6.021,1.042 6.51,1.042 false 6.021,1.156 6.271,1.156 6.271,1.156 6.271,1.052 true 0.927,3.177 1.208,3.531 0.281,0.354 18 false 7 5.042,1.188 5.323,1.542 0.281,0.354 18 false 6 6.542,0.438 6.823,0.792 0.281,0.354 18 false 5 2.229,3.063 2.51,3.417 0.281,0.354 18 false 4 3.26,3.656 3.542,4.01 0.281,0.354 18 false 3 6.802,1.719 7.083,2.073 0.281,0.354 18 false 2 5.635,3.177 5.917,3.531 0.281,0.354 18 false 1 4.635,1.49 4.948,1.688 0.313,0.198 10 false *1 5.531,4.083 5.844,4.281 0.313,0.198 10 false *2 6.563,0.927 6.719,1.125 0.156,0.198 10 false ● 2.802,0.531 3.115,0.729 0.313,0.198 10 false x2 5.427,0.865 5.74,1.063 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 COOLER THERMISTOR 88625 (Click here) - -
2 NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY 88501 - - -
3 HEATER RADIATOR UNIT SUB-ASSEMBLY 87107A - - -
4 HEATER CLAMP 87124B - - -
5 COOLER EXPANSION VALVE 88515 (Click here) - -
6 COOLER PIPE GROMMET 88897K - - -
7 BLOWER ASSEMBLY 87130D - - -

*1 UPPER HEATER CASE *2 LOWER HEATER CASE
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

for Gasoline Model (for HFC-134a(R134a)):
Compressor oil ND-OIL 8 or equivalent
for Gasoline Model (for HFO-1234yf(R1234yf)):
Compressor oil ND-OIL 12 or equivalent
for HV Model:
Compressor oil ND-OIL 11 or equivalent
- -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for LHD and RHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 88625 1.INSTALL NO. 1 COOLER THERMISTOR

a.
I116904C02
4.24,0.406 4.698,0.74 true 5.063,0.76 5.313,0.438 false 2.26,0.792 2.49,0.49 true 2.667,0.469 2.875,0.75 true 4.125,0.302 4.438,0.5 0.313,0.198 10 false a 5.354,0.344 5.667,0.542 0.313,0.198 10 false b 2.802,0.771 3.021,0.979 0.219,0.208 10 true *b 2.125,0.813 2.333,1.021 0.208,0.208 10 true *a 4.802,0.229 5.115,0.427 0.313,0.198 10 false X 1.208,0.719 1.521,0.917 0.313,0.198 10 false A 2.25,1.469 2.563,1.667 0.313,0.198 10 false B 0.5,0.073 0.781,0.427 0.281,0.354 18 false i
*a Securing Part *b Sensor Part


i.

Install the No. 1 cooler thermistor as shown in the illustration.

Part Length Part Length
A 45 to 55 mm (1.77 to 2.17 in.) B 61.1 mm (2.41 in.)

NOTICE:
·

Be sure to insert the No. 1 cooler thermistor only once because reinserting it into the same position will not allow it to be firmly secured.

·

When reusing the No. 1 cooler evaporator sub-assembly, insert the No. 1 cooler thermistor one row next to the one that has been used previously (X in the illustration).

·

After inserting the No. 1 cooler thermistor, do not apply excessive force to the wire.

·

Directly insert the No. 1 cooler thermistor until the edge of the plastic case "a" comes into contact with the No. 1 cooler evaporator sub-assembly "b".





Hide 88501 2.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

Hide 87107A 3.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

Hide 87124B 4.INSTALL HEATER CLAMP

Hide 88515 5.INSTALL COOLER EXPANSION VALVE

Z101186

Click here(Click here)

Hide 88897K 6.INSTALL COOLER PIPE GROMMET