Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Front) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0438550 ULTRASONIC SENSOR(for Front) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Front)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
E463470N02
1.521,1.958 1.979,1.958 false 1.323,1.833 1.604,2.188 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ULTRASONIC SENSOR CUSHION SET - (Click here) - -

E449658N04
0.292,0.677 1.635,1.833 1.344,1.156 5.115,3.99 6.688,5.271 1.573,1.281 5.813,2.979 5.688,2.979 5.688,2.979 5.604,2.781 false 5.688,4.51 5.688,4.271 false 6.427,4.938 6.427,4.656 false 5.375,1.667 5.708,1.667 false 4.646,1.125 4.979,1.125 false 1.188,1.573 1.438,1.573 false 0.771,1.094 1.073,1.094 false 3.719,0.281 3.885,0.281 3.885,0.281 3.969,0.615 false 2.813,0.25 2.979,0.25 2.979,0.25 3.208,0.625 false 1.625,5.229 1.625,4.896 false 6.5,0.292 6.708,0.292 false 5.938,2.177 6.271,2.177 false 1.563,5.25 1.844,5.604 0.281,0.354 18 false 7 6.333,2.01 6.615,2.365 0.281,0.354 18 false 5 6.219,2.865 6.5,3.219 0.281,0.354 18 false 2 6.073,2.917 6.271,3.167 0.198,0.25 10 false ● 6.375,4.958 6.656,5.313 0.281,0.354 18 false 6 5.771,4.542 6.052,4.896 0.281,0.354 18 false 3 5.625,4.573 5.823,4.823 0.198,0.25 10 false ● 5.771,1.49 6.052,1.844 0.281,0.354 18 false 4 5.042,0.979 5.323,1.333 0.281,0.354 18 false 4 3.531,0.125 3.813,0.479 0.281,0.354 18 false 5 2.635,0.104 2.917,0.458 0.281,0.354 18 false 2 2.521,0.156 2.719,0.406 0.198,0.25 10 false ● 1,1.417 1.281,1.771 0.281,0.354 18 false 3 0.844,1.458 1.042,1.708 0.198,0.25 10 false ● 1.125,0.948 1.406,1.302 0.281,0.354 18 false 6 5.188,4.031 5.563,4.271 0.375,0.24 12 false *A 0.385,0.74 0.76,0.979 0.375,0.24 12 false *A 5.365,0.146 5.646,0.5 0.281,0.354 18 false 8 5.542,0.198 5.917,0.438 0.375,0.24 12 false (*B) 5.844,0.146 6.26,0.5 0.417,0.354 18 false , 9 6.167,0.208 6.542,0.448 0.375,0.24 12 false (*C)

Procedure Part Name Code
Z101186

Z101188

Z101187

2 FRONT CORNER ULTRASONIC SENSOR RETAINER 89C48D (Click here) - -
3 FRONT SIDE ULTRASONIC SENSOR RETAINER 89C48F (Click here) - -
4 FRONT CENTER ULTRASONIC SENSOR 89341L - - -
5 FRONT CORNER ULTRASONIC SENSOR 89341K - - -
6 FRONT SIDE ULTRASONIC SENSOR 89341M - - -
7 FRONT BUMPER ASSEMBLY - - - -
8 PERFORM CALIBRATION - - - (Click here)
9 PERFORM CALIBRATION - - - (Click here)

*A w/ Advanced Park *B w/ Parking Support Brake System
*C w/o Parking Support Brake System - -
● Non-reusable part - -

PROCEDURE

Hide 1.INSTALL ULTRASONIC SENSOR CUSHION SET

Z101186

NOTICE:

Perform this procedure only when replacement of the ultrasonic sensor cushion set is necessary.



Hide 89C48D 2.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER

Z101186

NOTICE:
·

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

·

If a front corner ultrasonic sensor retainer has been removed, replace it with a new one.




a.
E449660C01
4.281,5.563 4.021,5.365 true 2.698,3.563 2.438,3.365 true 0.365,0.156 0.646,0.51 0.281,0.354 18 true i 4.729,0.146 5.01,0.5 0.281,0.354 18 false ii 4.427,2.083 4.708,2.438 0.281,0.354 18 false iv 0.406,1.99 0.615,2.26 0.208,0.271 18 true iii 4.865,5.469 5.115,5.75 0.25,0.281 18 true v 4.302,5.51 4.49,5.688 0.188,0.177 10 true *a 2.698,3.479 2.885,3.656 0.188,0.177 10 true *a
*a Scribed Line - -
V100144

Primer Application - -


i.

Clean the surface of the front bumper assembly.

1. Using a heat light, heat the front bumper assembly.

2. Remove any remaining double-sided tape from the front bumper assembly.

3. Wipe off any adhesive residue with cleaner.

NOTICE:
·

Installing the front corner ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Cover the sensor installation hole with a 20 mm (0.787 in.) circular piece of tape.


iii.

Apply primer to front bumper assembly on the installation area of the front corner ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the front corner ultrasonic sensor retainer has been attached.



1. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))


2. Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.


iv.

Remove the peeling paper of a new front corner ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



v.

Align the front corner ultrasonic sensor retainer with front corner ultrasonic sensor with the scribed line on the front bumper assembly and install it as shown in the illustration.

NOTICE:
·

Ensure that the front corner ultrasonic sensor tip is correctly inserted into the sensor installation hole of the front bumper assembly.

·

The application strength of the front corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

·

Apply pressure so that it does not lift up from the front bumper assembly.



HINT:

Pushing force: 50 N (5.1 kgf) for 3 seconds




b.

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


Hide 89C48F 3.INSTALL FRONT SIDE ULTRASONIC SENSOR RETAINER (w/ Advanced Park)

Z101186

NOTICE:
·

Perform this procedure only when replacement of the front side ultrasonic sensor retainer is necessary.

·

If a front side ultrasonic sensor retainer has been removed, replace it with a new one.




a.
E449659C01
1.396,4.51 1.083,4.74 1.083,4.74 1.656,4.5 true 2.302,5.396 2.531,5.469 true 2.323,3.104 2.854,3.365 true 5.729,5.385 5.885,5.49 true 5.938,4.271 6.188,4.333 true 5.625,5.333 5.938,5.052 true 0.375,0.156 0.573,0.51 0.198,0.354 18 true i 4.76,0.146 4.958,0.5 0.198,0.354 18 false ii 0.344,1.885 0.594,2.24 0.25,0.354 18 false iii 4.552,1.875 4.938,2.229 0.385,0.354 18 false iv 0.875,4.667 1.063,4.854 0.188,0.188 10 true *b 2.563,5.406 2.781,5.594 0.219,0.188 10 true *a 0.635,4.594 0.844,4.875 0.208,0.281 18 true v 3.083,5.365 3.344,5.656 0.26,0.292 18 true vi 2.854,3.292 3.073,3.479 0.219,0.188 10 true *a 6.25,4.271 6.438,4.458 0.188,0.188 10 true *b 5.917,5.406 6.135,5.594 0.219,0.188 10 true *a 6.49,4.188 6.698,4.469 0.208,0.281 18 true v 6.479,5.354 6.74,5.646 0.26,0.292 18 true vi 6.208,4.865 6.417,5.146 0.208,0.281 18 true v 5.969,4.958 6.156,5.146 0.188,0.188 10 true *b 0.281,4.052 0.656,4.292 0.375,0.24 12 false *A 3.688,4.042 4.063,4.281 0.375,0.24 12 false *B
*A for LH Side *B for RH Side
*a Scribed Line *b Identification Code
V100144

Primer Application - -


i.

Clean the surface of the front bumper assembly.

1. Using a heat light, heat the front bumper assembly.

2. Remove any remaining double-sided tape from the front bumper assembly.

3. Wipe off any adhesive residue with cleaner.

NOTICE:
·

Installing the front side ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Cover the sensor installation hole with a 25 mm (0.984 in.) circular piece of tape.


iii.

Apply primer to front bumper assembly on the installation area of the front side ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the front side ultrasonic sensor retainer has been attached.



1. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))


2. Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.


iv.

Remove the peeling paper of a new front side ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



v.

Check that the identification codes on the front bumper assembly and the front side ultrasonic sensor retainer are identical.


vi.

Align the front side ultrasonic sensor retainer with front side ultrasonic sensor with the scribed line on the front bumper assembly and install it as shown in the illustration.

NOTICE:
·

Ensure that the front side ultrasonic sensor tip is correctly inserted into the sensor installation hole of the front bumper assembly.

·

The application strength of the front side ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

·

Apply pressure so that it does not lift up from the front bumper assembly.



HINT:

Pushing force: 50 N (5.1 kgf) for 3 seconds




Hide 89341L 4.INSTALL FRONT CENTER ULTRASONIC SENSOR

Hide 89341K 5.INSTALL FRONT CORNER ULTRASONIC SENSOR

Hide 89341M 6.INSTALL FRONT SIDE ULTRASONIC SENSOR (w/ Advanced Park)

Hide 7.INSTALL FRONT BUMPER ASSEMBLY

Hide 8.PERFORM CALIBRATION (w/ Parking Support Brake System)