Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for RHD) › from 2021.07
RM3700E _57 Power Source / Network _093028 POWER DISTRIBUTION _0483099 MAIN BODY ECU(for RHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
E448345N02
3.833,1.75 6.417,2.667 2.583,0.917 3.833,1 4.865,1.188 1.031,0.188 3.667,3.167 4.677,3.333 1.01,0.167 6,3.25 6.5,3.25 false 5.552,2.302 5.958,2.302 false 6.49,0.24 6.823,0.24 false 1.948,3.063 2.26,3.063 2.26,3.063 2.583,2.625 true 3.5,1.083 3.833,1.083 false 3.25,1.583 3.5,1.083 true 3.333,3.25 3.667,3.25 false 3.167,3.5 3.333,3.25 false 4.344,2.427 4.583,2.427 false 1.771,2.917 2.052,3.271 0.281,0.354 18 false 4 6.26,0.115 6.542,0.469 0.281,0.354 18 false 1 4.625,2.302 4.906,2.656 0.281,0.354 18 false 3 5.802,3.146 6.083,3.5 0.281,0.354 18 false 2 3.906,1.021 5.115,1.26 1.208,0.24 8 false 8.0 (82, 71 in.*lbf) 5.365,2.25 5.677,2.448 0.313,0.198 10 false *1 3.708,3.177 4.917,3.417 1.208,0.24 8 false 8.0 (82, 71 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 89221 (Click here) - -
3 POWER DISTRIBUTION BOX ASSEMBLY 82730G - - -
4 POWER DISTRIBUTION BOX ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU - (Click here) - -

*1 ECU INTEGRATION BOX LH - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

E473589N01
6.51,0.24 6.823,0.24 false 6.125,4.865 6.125,5.198 false 6.531,0.594 6.802,0.594 false 6.042,2.5 6.458,2.5 false 6.354,1.281 6.688,1.281 false 3.833,0.781 4.25,0.781 false 6.042,3.302 6.458,3.302 false 1.771,5.271 2.188,5.271 false 0.698,4.302 1.115,4.302 false 0.375,1.469 0.792,1.469 false 1.344,2.656 1.76,2.656 false 3.906,4.792 3.906,5.125 false 3.552,3.625 3.552,3.885 false 3,2.271 3,2.604 false 4.26,2.26 4.573,2.458 0.313,0.198 10 false x2 4.552,2.104 4.865,2.302 0.313,0.198 10 false x3 6.219,0.094 6.635,0.448 0.417,0.354 18 false 17 6.219,0.469 6.625,0.823 0.406,0.354 18 false 18 6.5,2.375 6.896,2.802 0.396,0.427 18 false 16 6.729,1.135 7.104,1.5 0.375,0.365 18 false 14 4.302,0.656 4.688,1.021 0.385,0.365 18 false 15 6.521,3.167 6.917,3.594 0.396,0.427 18 false 13 6.01,5.229 6.375,5.625 0.365,0.396 18 false 12 1.51,5.135 1.875,5.5 0.365,0.365 18 false 11 0.385,4.156 0.854,4.573 0.469,0.417 18 false 10 0.844,1.333 1.219,1.719 0.375,0.385 18 false 9 1.813,2.521 2.188,2.906 0.375,0.385 18 false 8 3.854,5.146 4.229,5.531 0.375,0.385 18 false 7 3.604,3.885 3.979,4.271 0.375,0.385 18 false 6 2.948,2.615 3.323,3 0.375,0.385 18 false 5

Procedure Part Name Code
Z101186

Z101188

Z101187

5 LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL 55433B - - -
6 GLOVE COMPARTMENT DOOR ASSEMBLY 55550 (Click here) - -
7 NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55607 - - -
8 NO. 1 INSTRUMENT SIDE PANEL 55317E - - -
9 FRONT DOOR OPENING TRIM WEATHERSTRIP LH 62312B - - -
10 COWL SIDE TRIM BOARD LH 62112 - - -
11 FRONT DOOR SCUFF PLATE LH 67914B - - -
12 CONSOLE BOX ASSEMBLY 58810J - - -
13 SWITCH HOLE BASE SUB-ASSEMBLY 55407B - - -
14 INSTRUMENT PANEL FINISH PANEL 55431A - - -
15 LOWER INSTRUMENT PANEL FINISH PANEL 55432B - - -
16 CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH 55475B - - -
17 NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
18 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)

PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

When installing the main body ECU (multiplex network body ECU), always replace it with a new one.




Hide 89221 2.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Z101186

NOTICE:
·

Make sure that the connecting surfaces are free of foreign matter.

·

Do not touch the main body ECU (multiplex network body ECU) connector.




a.
E448347C02
0.521,0.74 0.813,0.875 true 2.667,0.74 2.958,0.875 true 3.74,0.792 4.094,0.521 true 5.969,0.76 6.344,0.531 true 2.24,2.927 2.615,2.698 true 4.083,2.938 4.323,2.938 true 4.406,2.958 4.594,3.167 true 0.354,0.656 0.667,0.854 0.313,0.198 10 false *b 0.49,1.302 0.802,1.5 0.313,0.198 10 false *a 2.49,0.656 2.802,0.854 0.313,0.198 10 false *b 4.135,0.448 4.448,0.646 0.313,0.198 10 false *c 6.375,0.448 6.688,0.646 0.313,0.198 10 false *c 2.667,2.625 2.979,2.823 0.313,0.198 10 false *d 4.573,3.188 4.885,3.385 0.313,0.198 10 false *1 3.917,2.865 4.229,3.063 0.313,0.198 10 false *2 1.354,1.948 1.677,2.281 0.323,0.333 18 false iv 5.198,1.958 5.521,2.292 0.323,0.333 18 false v 5.208,0.094 5.531,0.427 0.323,0.333 18 false iii 2.885,0.094 3.208,0.427 0.323,0.333 18 false ii 0.448,0.104 0.771,0.438 0.323,0.333 18 false i
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)
*a 20° or more *b Housing Sidewall
*c Side A *d Center of Rotation (Contacts Surface A)
V100145

Push Area
V100135

Set
V100136

Slide
V113147

Install in this Direction
V113148

Rotate in this Direction - -


i.

Set the main body ECU (multiplex network body ECU) to the position where the guide of the main body ECU (multiplex network body ECU) contacts the housing sidewall of the power distribution box assembly as shown in the illustration.

HINT:

Make sure to keep the angle at 20° or more as shown in the illustration.



ii.

Slide the main body ECU (multiplex network body ECU) along the housing sidewall as shown in the illustration and engage the guides.


iii.

While keeping the main body ECU (multiplex network body ECU) in contact with side A of the power distribution box assembly (axis of rotation), lower it as shown in the illustration.

NOTICE:

Do not strike or apply excessive force to the side surface of the main body ECU (multiplex network body ECU).



iv.

While pressing the main body ECU (multiplex network body ECU) against side A (center of rotation) of the power distribution box assembly, rotate it until it enters the lock of the power distribution box assembly.


v.

Press the push area until the claw engages to install the main body ECU (multiplex network body ECU).

NOTICE:
·

Make sure to press only the push area.

·

Confirm the engagement of the main body ECU (multiplex network body ECU) and power distribution box assembly by listening for the click sound of the lock engaging.



HINT:

If a click sound cannot be heard, visually check the engagement of the lock. The engagement can also be confirmed if the main body ECU (multiplex network body ECU) and power distribution box assembly are flush.




Hide 82730G 3.INSTALL POWER DISTRIBUTION BOX ASSEMBLY

Hide 4.INSTALL POWER DISTRIBUTION BOX ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU

a.
E448348C02
1.188,0.354 1.323,0.198 false 0.646,1.385 0.865,1.323 false 1.979,0.417 2.146,0.688 0.167,0.271 18 true i 0.573,0.063 0.781,0.333 0.208,0.271 18 true ii 4,0.115 4.208,0.385 0.208,0.271 18 false iii 1.365,0.083 1.552,0.281 0.188,0.198 10 true *a 0.479,1.333 0.667,1.531 0.188,0.198 10 false *a
*a Lock Lever - -


i.

Connect the connector.


ii.

Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.


iii.

Engage the claws.



b.
E448349C01
3.083,1.552 3.281,1.75 0.198,0.198 10 true *b 3,0.063 3.198,0.26 0.198,0.198 10 true *a 1.938,0.156 2.219,0.51 0.281,0.354 18 false i 4,0.063 4.198,0.406 0.198,0.344 18 true ii 4.281,1.479 4.49,1.76 0.208,0.281 18 true ii 3.448,1.073 3.656,1.354 0.208,0.281 18 true ii 3.302,0.427 3.51,0.708 0.208,0.281 18 true ii
*a Nut (A) *b Bolt (A)


i.

Engage the claws.


ii.

Install the power distribution box assembly with multiplex network body ECU with the 2 bolts and 2 nuts.

Torque:
Nut (A) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt (A) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)



c.
E448350C02
4.281,0.365 4.406,0.208 false 4.042,1.583 4.302,1.385 true 0.729,0.385 1.01,0.74 0.281,0.354 18 false i 2.531,0.167 2.729,0.438 0.198,0.271 18 true ii 5.052,0.198 5.292,0.396 0.24,0.198 12 true *A 5.573,0.198 5.792,0.479 0.219,0.281 18 true iii 0.719,2.104 1,2.458 0.281,0.354 18 false i 4.052,2.406 4.281,2.698 0.229,0.292 18 true i 4.427,0.094 4.656,0.302 0.229,0.208 10 true *a 4.333,1.302 4.563,1.51 0.229,0.208 10 true *a 4.073,2.792 4.302,3.083 0.229,0.292 18 true i
*A for HV Model - -
*a Lock Lever - -


i.

Connect the each connector.


ii.

Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.


iii.

for HV Model:

1. Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.



d.
E448351C01
2.156,0.115 2.323,0.385 0.167,0.271 18 true i

i.

Engage the clamps.



Hide 55433B 5.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 55550 6.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Z101186

Click here(Click here)

Hide 55607 7.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55317E 8.INSTALL NO. 1 INSTRUMENT SIDE PANEL

Hide 62312B 9.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62112 10.INSTALL COWL SIDE TRIM BOARD LH

Hide 67914B 11.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 58810J 12.INSTALL CONSOLE BOX ASSEMBLY

Hide 55407B 13.INSTALL SWITCH HOLE BASE SUB-ASSEMBLY

Hide 55431A 14.INSTALL INSTRUMENT PANEL FINISH PANEL

Hide 55432B 15.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL

Hide 55475B 16.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 17.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 18. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART