| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| C061012 | Right Electric Parking Brake Actuator Control Circuit Short to Battery | ·
Diagnosis Condition: Electric parking brake not operating ·
Malfunction Status: The ECU power supply is normal but there is a malfunction in the electric parking brake actuator RH internal circuit (short to +B). ·
Detection Time: Approximately 1 second |
·
Parking brake actuator assembly RH ·
No. 1 parking brake wire assembly ·
Wire harness and connector ·
Skid control ECU (brake actuator assembly) |
DTC stored | Brake/EPB | A | An electric parking brake system malfunction is displayed on the multi-information display. |
The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.
After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.
When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned to ON.
Pre-procedure1
Turn the ignition switch off.
Make sure the No. 1 parking brake wire assembly is securely installed.
Disconnect the u1 parking brake actuator assembly RH connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(u1)Location & Routingewd_type=routing;type=c;code=u1 Click Connector(u1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly RHewd_type=component;type=c;code=u1;pinno=2,1 |
||
| u1-2 (MRR+) - u1-1 (MRR-) | Electric parking brake not operating | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the uO3 No. 1 parking brake wire assembly connector.
Procedure1
| *a | Front view of wire harness connector
(to No. 1 Parking Brake Wire Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(uO3)Location & Routingewd_type=routing;type=w;code=uO3 Click Connector(uO3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO3;pinno=1,2 |
||
| uO3-1 - uO3-2 | Electric parking brake not operating | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the uO3 No. 1 parking brake wire assembly connector.
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| *a | Front view of wire harness connector | *b | (to Skid Control ECU (Brake Actuator Assembly)) |
| *c | (to No. 1 Parking Brake Wire Assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(uO3,A39)Location & Routingewd_type=routing;type=w,c;code=uO3,A39 Click Connector(uO3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO3;pinno=1,2 Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A39;pinno=2,3 |
||
| uO3-1 or A39-2 (MRR+) - Body ground | Always | Below 1 V |
| uO3-2 or A39-3 (MRR-) - Body ground | Always | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMMF Made RHD)>REMOVAL
NG