Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for HV Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093729 PARKING BRAKE _0483556 ELECTRIC PARKING BRAKE SYSTEM(for HV Model TMMF Made) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for HV Model TMMF Made)  C060E2A  Left Electric Parking Brake Actuator Signal Stuck In Range  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
C060E2A Left Electric Parking Brake Actuator Signal Stuck In Range
·

Diagnosis Condition:

Electric parking brake operating

·

Malfunction Status:

Motor locked, gear locked, free spinning

·

Detection Time:

-


·

Parking brake actuator assembly LH

·

No. 2 parking brake wire assembly

·

Wire harness and connector

·

Rear brake LH


DTC stored Brake/EPB B An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Electric parking brake operating ○ ○ ○
Malfunction Status Motor lock detected ○ - -
Gear lock detected - ○ -
Free spinning detected - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

CAUTION / NOTICE / HINT

NOTICE:
·

Although DTC C060E2A may be stored after entering pad replacement mode, this is not a malfunction.

·

Although DTC C060E2A may be stored after forcibly releasing the parking brake, this is not a malfunction.

·

To ensure that the electric parking brake does not operate, wait for 4 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned to ON.



PROCEDURE

1.CHECK DTC
a.

Using the GTS, check for DTCs other than DTC C060E2A.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
Only C060E2A is output A
C060E2A and other DTCs are output B



A

2.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

2.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the uO2 and u3 No. 2 parking brake wire assembly connectors.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

C430805C10
1.792,0.25 2.208,0.5 0.417,0.25 5,0.25 5.417,0.5 0.417,0.25 5.917,2.083 5.448,1.667 true 4.5,2.083 4.99,1.667 true 1.865,0.292 2.323,0.49 0.458,0.198 10 false uO2 5.104,0.292 5.563,0.49 0.458,0.198 10 false u3 5.844,2.125 6.385,2.365 0.542,0.24 10 false MRL+ 4.292,2.115 4.75,2.313 0.458,0.198 10 false MRL- 1.917,2.375 2.375,2.583 0.458,0.208 10 false *b 0.125,0.125 0.656,0.365 0.531,0.24 10 false *a 5.146,2.385 5.604,2.583 0.458,0.198 10 false *c
*a Front view of No. 2 Parking Brake Wire Assembly *b (to wire harness connector)
*c (to Parking Brake Actuator Assembly LH) - -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO2,u3)Location & Routing

Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wire

Click Connector(u3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LH

uO2-1 - u3-2 (MRL+) Always Below 1 Ω
uO2-1 or u3-2 (MRL+) - Body ground and other terminals Always 10 kΩ or higher
uO2-2 - u3-1 (MRL-) Always Below 1 Ω
uO2-2 or u3-1 (MRL-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Make sure the No. 2 parking brake wire assembly is securely installed.


c.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the u3 parking brake actuator assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A39,u3)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

Click Connector(u3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LH

A39-13 (MRL+) - u3-2 (MRL+) Always Below 1 Ω
A39-12 (MRL-) - u3-1 (MRL-) Always Below 1 Ω
A39-13 (MRL+) or u3-2 (MRL+) - Body ground Always 10 kΩ or higher
A39-12 (MRL-) or u3-1 (MRL-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK VEHICLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
for 2WD A
for AWD B



A

5.INSPECT REAR BRAKE AND PARKING BRAKE ACTUATOR ASSEMBLY LH (CHECK FOR ROTATING PARTS THAT ARE STUCK AND FOR FREE SPINNING ACTUATORS)

B

6.INSPECT REAR BRAKE AND PARKING BRAKE ACTUATOR ASSEMBLY LH (CHECK FOR ROTATING PARTS THAT ARE STUCK AND FOR FREE SPINNING ACTUATORS)
5.INSPECT REAR BRAKE AND PARKING BRAKE ACTUATOR ASSEMBLY LH (CHECK FOR ROTATING PARTS THAT ARE STUCK AND FOR FREE SPINNING ACTUATORS)

Pre-procedure1


b.

Turn the ignition switch off.


Procedure1

a.

Check that the rotating parts are not seized or the actuator is not spinning freely.

i.

Check that the parking brake actuator assembly LH is installed properly to the rear brake caliper and that it is not spinning freely.

HINT:

For the parking brake actuator assembly LH removal procedure: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for TMMF Made 2WD)>REMOVAL



ii.

Check that there is no damage to the rotating parts from the parking brake actuator assembly LH to the rear brake caliper.


iii.

Inspect the parking brake actuator assembly LH and check that it operates correctly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for TMMF Made 2WD)>INSPECTION


iv.

Check that the rear brake caliper threaded part rotates and that the rear disc brake piston moves outward.

HINT:

For the check procedures, refer to the parking brake forced release method when not using the GTS.

Click hereBrake>PARKING BRAKE>FORCED RELEASE>OPERATION METHOD


Result:
Result Proceed to
Parking brake actuator assembly LH is malfunctioning A
Other than parking brake actuator assembly LH is malfunctioning B




Post-procedure1

a.

Return to normal mode after work is complete.

HINT:

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model TMMF Made)>TEST MODE PROCEDURE




A

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

B

REPAIR OR REPLACE ABNORMAL PARTS

6.INSPECT REAR BRAKE AND PARKING BRAKE ACTUATOR ASSEMBLY LH (CHECK FOR ROTATING PARTS THAT ARE STUCK AND FOR FREE SPINNING ACTUATORS)

Pre-procedure1


b.

Turn the ignition switch off.


Procedure1

a.

Check that the rotating parts are not seized or the actuator is not spinning freely.

i.

Check that the parking brake actuator assembly LH is installed properly to the rear brake caliper and that it is not spinning freely.

HINT:

For the parking brake actuator assembly LH removal procedure: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for AWD)>REMOVAL



ii.

Check that there is no damage to the rotating parts from the parking brake actuator assembly LH to the rear brake caliper.


iii.

Inspect the parking brake actuator assembly LH and check that it operates correctly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for AWD)>INSPECTION


iv.

Check that the rear brake caliper threaded part rotates and that the rear disc brake piston moves outward.

HINT:

For the check procedures, refer to the parking brake forced release method when not using the GTS.

Click hereBrake>PARKING BRAKE>FORCED RELEASE>OPERATION METHOD


Result:
Result Proceed to
Parking brake actuator assembly LH is malfunctioning A
Other than parking brake actuator assembly LH is malfunctioning B




Post-procedure1

a.

Return to normal mode after work is complete.

HINT:

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model TMMF Made)>TEST MODE PROCEDURE




A

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH

B

REPAIR OR REPLACE ABNORMAL PARTS