When the vehicle is being driven in a straight line at 15 km/h (9 mph) for 1 second or more, the skid control ECU (brake actuator assembly) calculates the steering sensor zero point and updates the zero point if the difference between the calculated zero point and current zero point is between 10° and 15°. The ECU also stores previous zero points.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C052646 | Steering Angle Sensor Module Calibration / Parameter Memory Failure | After the steering sensor zero point is obtained, the zero point is lost due to power supply fluctuations, etc. and cannot be reobtained when the vehicle speed is 15 km/h (9 mph) or more. | ·
Steering sensor ·
Yaw rate and acceleration sensor (airbag sensor assembly) |
Brake/EPB | B |
Because this DTC is related to a temporary loss of steering angle zero point calibration, before proceeding with the inspection, it is useful to confirm whether the power source voltage was interrupted by an operation such as removal or disconnection of the battery.
When DTC U007488 and/or U012687 is output together with DTC C052646, inspect and repair the trouble areas indicated by DTC U007488 and/or U012687 first.
If a speed sensor, yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, the steering sensor may also appear to be malfunctioning even when normal.
If DTCs related to a speed sensor, yaw rate and acceleration sensor (airbag sensor assembly) are output, perform troubleshooting for those DTCs before inspecting the steering sensor.
Turn the ignition switch to ON again and check that no CAN communication system DTCs are output.
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are output. | A |
| CAN communication system DTCs are not output. | B |
A
B
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Start the engine and perform a road test.
Drive the vehicle at a speed of 15 km/h (9 mph) and turn the steering wheel to the right and left.
Procedure1
Check that no speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
| Result | Proceed to |
|---|---|
| C052646 is output. | A |
| Speed sensor and/or yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output. | B |
| C052646 is not output. | C |
Post-procedure1
None
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Pre-procedure1
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for at least 1 second.
Procedure1
Check that the steering wheel is correctly centered while driving straight ahead.
The steering wheel is correctly centered.
If front wheel alignment and steering are adjusted as a result of an off-center steering wheel, acquire the yaw rate and acceleration sensor zero point again after the adjustments are completed.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Start the engine and perform a road test.
Drive the vehicle at a speed of 15 km/h (9 mph) and turn the steering wheel to the right and left.
Procedure1
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C052646 is not output | A |
| C052646 is output | B |
If DTC C052646 is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero point calibration, such as a loss of calibration due to the power source voltage being low.
Post-procedure1
None
A
B