Refer to DTC P008A00.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P008A00
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| P008B00 | Low Pressure Fuel System Pressure - Too High | The actual fuel pressure value is higher than target fuel pressure by a certain amount or more (1 trip detection logic). | ·
Fuel pump control ECU ·
Fuel pressure sensor ·
ECM |
Does not come on | Engine | B | SAE Code: P008B |
If the fuel pressure increases despite a decrease request signal being sent to the fuel pump control ECU by the ECM, the ECM will store this DTC.
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON [A].
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
With the engine running, drive the vehicle for 15 minutes or more [C].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
If the engine stops, further depress the accelerator pedal to restart the engine.
Enter the following menus: Powertrain / Engine / Trouble Codes [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P008B00.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, perform steps [B] through [D] again.
Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY
(Select Powertrain in Health Check and then check the time stamp data.)
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P008B00 and other DTCs are output | A |
| P008B00 is output | B |
If any DTCs other than P008B00 are output, troubleshoot those DTCs first.
A
B
Pre-procedure1
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine.
Procedure1
Record the Low Fuel Pressure Sensor value.
| Tester Display |
|---|
| Low Fuel Pressure Sensor |
| Proceed to |
|---|
| NEXT |
Post-procedure1
None.
NEXT
Pre-procedure1
Turn the ignition switch off.
Discharge the fuel pressure.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
Remove the EFI-MAIN NO. 2 fuse from the No. 1 engine room relay block.
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine.
After the engine has stopped on its own, turn the ignition switch off.
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Crank the engine again and make sure that the engine does not start.
Install the EFI-MAIN NO. 2 fuse.
Procedure1
Read the Data List.
| Tester Display |
|---|
| Low Fuel Pressure Sensor |
Compare the Low Fuel Pressure Sensor value recorded with the engine running with the Low Fuel Pressure Sensor value currently shown on the GTS.
| Result | Proceed to |
|---|---|
| Low Fuel Pressure Sensor value drops | A |
| Low Fuel Pressure Sensor value is maintained | B |
Post-procedure1
None.
A
B
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL PRESSURE SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the fuel pressure sensor.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Pre-procedure1
Install the fuel pressure gauge.
Procedure1
Compare the values in the Data List using the GTS and the fuel pressure gauge when the Active Test was performed.
| Active Test Display |
|---|
| Control the Fuel Pump Duty Ratio (Brushless) |
| Data List Display |
|---|
| Fuel Pump Control Duty Ratio |
| Low Fuel Pressure Sensor |
| GTS Operation | Standard |
|---|---|
| Low | Data List value and fuel pressure gauge value are within +/-50 kPa of each other |
| High |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL PRESSURE SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the fuel pressure sensor.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Pre-procedure1
Install the fuel pressure gauge.
Procedure1
Read the values on the Data List and the fuel pressure gauge when the Active Test was performed.
| Active Test Display |
|---|
| Control the Fuel Pump Duty Ratio (Brushless) |
| Data List Display |
|---|
| Fuel Pump Control Duty Ratio |
| Low Fuel Pressure Sensor |
| GTS Operation | Low Fuel Pressure Sensor | Fuel Pressure Gauge | Proceed to |
|---|---|---|---|
| Low | Below 600 kPag | Below 600 kPa (6.1 kgf/cm2, 87 psi) | A |
| 600 kPag or higher | 600 kPa (6.1 kgf/cm2, 87 psi) or higher | B |
Post-procedure1
None.
A
B
Pre-procedure1
None.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Procedure1
Perform All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P008B00.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P008B00 is output) |
B |
Post-procedure1
None.
A
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
B