Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093729 PARKING BRAKE _0483555 ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model TMMF Made) J

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model TMMF Made)  Electric Parking Brake System AUTO Function Circuit  


DESCRIPTION

for Manual Transaxle:

The electric parking brake system AUTO function (IG-OFF linked function) is controlled by the skid control ECU (brake actuator assembly) based on whether it receives input voltage or not.

When the ignition switch is turned off, the electric parking brake system AUTO function (IG-OFF linked function) automatically operates to apply the electric parking brake.


for CVT:

The skid control ECU (brake actuator assembly) receives shift position signals from the ECM via CAN communication to control the electric parking brake system AUTO function (shift-linked function).

The electric parking brake system AUTO function (shift-linked function) is automatically disabled when the ignition switch is ON, the brake pedal is depressed and the shift lever is moved out of P. Then, if the shift lever is moved to P, the AUTO function (shift-linked function) automatically operates to apply the electric parking brake.


WIRING DIAGRAM

for Manual Transaxle
C397563E02
2.521,0.542 2.979,0.74 0.458,0.198 10 false IGR 1.583,1.958 3.167,2.698 1.583,0.74 10 false Skid Control ECU (Brake Actuator Assembly) 3.656,0.448 4.198,0.667 0.542,0.219 10 false *1 2.844,0.458 3.302,0.656 0.458,0.198 10 false 36 1.583,1.75 2,2.115 0.417,0.365 10 false A39 4.479,0.708 5.719,0.948 1.24,0.24 10 false ECU-IGR NO. 3 0.083,1.521 1.479,1.896 1.396,0.375 10 false *1: w/o Stop and Start System 0.104,2.177 1.417,2.583 1.313,0.406 10 false *2: w/ Stop and Start System 3.656,1.229 4.198,1.448 0.542,0.219 10 false *2 4.583,1.25 5.125,1.469 0.542,0.219 10 false 23 4.865,1.365 5.406,1.583 0.542,0.219 10 false IG31 4.76,1.844 5.302,2.063 0.542,0.219 10 false H43 4.75,2.021 6.74,2.406 1.99,0.385 10 false Engine Stop and Start ECU

for CVT
C396297E15
0.958,0.656 3.042,0.917 2.083,0.26 10 false TCM 0.938,1.063 3.073,1.448 2.135,0.385 10 false - Shift Position Signal 5.719,1.479 6.844,2.042 1.125,0.563 10 false Skid Control ECU (Brake Actuator Assembly) 1.25,2.281 3.385,2.667 2.135,0.385 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

The AUTO function (IG-OFF linked function) will not automatically operate if the electric parking brake switch assembly is moved to the release side when the ignition switch is turned off. (for Manual Transaxle)

·

The AUTO function (shift-linked function) will not be automatically disabled when the ignition switch is ON, the brake pedal is depressed and the shift lever is moved out from P if the electric parking brake switch assembly is moved to the engage side. The AUTO function (shift-linked function) will not automatically operate to apply the electric parking brake when the shift lever is moved to P if the electric parking brake switch assembly is moved to the release side. (for CVT)

·

The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.

·

Inspect the fuses for circuits related to this system before performing the following procedure. (for Manual Transaxle)

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned to ON.



PROCEDURE

1.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification.

Result:
Result Proceed to
for Manual Transaxle A
for CVT B




A

2.CHECK VEHICLE SPECIFICATION

B

6.CHECK DTC (CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM)
2.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification.

Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B




A

3.CHECK FOR SHORT TO +B

B

5.CHECK FOR SHORT TO +B
3.CHECK FOR SHORT TO +B
a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A39)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A39-36 (IGR) - Body ground IG OFF Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ENGINE STOP AND START ECU)
4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ENGINE STOP AND START ECU)
a.

Turn the ignition switch off.


b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the H43 engine stop and start ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A39)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A39-36 (IGR) - Body ground IG OFF Below 1 V


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FOR SHORT TO +B
a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A39)Location & Routing

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A39-36 (IGR) - Body ground IG OFF Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK DTC (CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM)
a.

Check for DTCs.

Powertrain > Transmission > Trouble Codes
50001 373
Result:
Result Proceed to
DTC is not output A
DTC is output B




A

B