Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093687 NAVIGATION / MULTI INFO DISPLAY _0441739 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Reverse Signal Circuit  


DESCRIPTION

for Gasoline Model (for Manual Transaxle)

The radio and display receiver assembly receives a reverse signal from the back-up light switch assembly.


for Gasoline Model (for CVT)

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly.


for HV Model

The radio and display receiver assembly receives a reverse signal from the power distribution box assembly.


WIRING DIAGRAM

E445966E08
5.448,1.042 5.906,1.24 0.458,0.198 10 false REV 5.417,2.927 5.875,3.125 0.458,0.198 10 false H79 5.406,3.083 6.604,3.469 1.198,0.385 10 false Radio and Display Receiver Assembly 5.198,0.906 5.656,1.104 0.458,0.198 10 false 28 3.938,0.906 4.396,1.104 0.458,0.198 10 false 2 4.292,2.229 4.75,2.427 0.458,0.198 10 false *1 0.74,1.448 2.135,1.75 1.396,0.302 10 false 4C 0.146,3.042 2.906,3.365 2.76,0.323 10 false *1: for Gasoline Model 0.74,1.594 3.729,1.833 2.99,0.24 10 false Power Distribution Box Assembly 4.198,1.115 4.656,1.313 0.458,0.198 10 false *2 1.417,2.104 4.406,2.344 2.99,0.24 10 false from Back-up Light Switch Assembly*3 0.979,2.427 4.125,2.656 3.146,0.229 10 false from Park/Neutral Position Switch Assembly*4 2.417,3.042 5.177,3.365 2.76,0.323 10 false *3: for Manual Transaxle 0.125,3.385 2.031,3.656 1.906,0.271 10 false *2: for HV Model 2.417,3.385 4.323,3.656 1.906,0.271 10 false *4: for CVT

PROCEDURE

1.CHECK BACK-UP LIGHT
a.

Move the shift lever to R and check if the back-up lights come on.

OK:

The back-up lights come on.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)

NG

2.CHECK HARNESS AND CONNECTOR (REVERSE SIGNAL)
a.

Disconnect the H79 radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H79)Location & Routing

Click Connector(H79)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H79-28 (REV) - Body ground Ignition switch ON
Shift lever in R
11 to 14 V
H79-28 (REV) - Body ground Ignition switch ON
Shift lever not in R
Below 1 V



Result:
Result Proceed to
OK A
NG (for Gasoline Model) B
NG (for HV Model) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the H79 radio and display receiver assembly connector.


b.

Disconnect the 4C power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H79)Location & Routing

Click Connector(H79)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H79-28 (REV) - 4C-2 Always Below 1 Ω
H79-28 (REV) or 4C-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR