| *A | w/o Vertical Adjuster | *B | w/ Vertical Adjuster |
| *C | w/ Under Tray | - | - |
| *1 | FRONT SEAT ANCHOR PLATE | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 12 | SEPARATE TYPE FRONT SEATBACK ASSEMBLY | - | - | - | - |
| 13 | SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD | - | - | - | - |
| 14 | CONNECTOR HOLDER | 82667D | - | - | - |
| 15 | OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD) | 71512S | - | - | - |
| *A | for Standard Seat Type | *B | for Sports Seat Type |
| *1 | SEPARATE TYPE FRONT SEAT CUSHION COVER | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the occupant detection sensor removal/installation are shown below.
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Wear protective gloves. Sharp areas on the parts may injure your hands.
If a front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad, separate type front seatback cover and front seatback pad with cover with the necessary parts in accordance with the extent of the collision damage.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD.
The following procedure is for LHD.
72925
2.REMOVE FRONT SEAT CUSHION COVER (w/ Under Tray)
73508A
3.REMOVE NO. 2 FRONT SEAT UNDER TRAY RAIL SUB-ASSEMBLY (w/ Under Tray)
73240
4.REMOVE FRONT SEAT INNER BELT ASSEMBLY
72494
5.REMOVE VERTICAL ADJUSTING HANDLE (w/ Vertical Adjuster)
Use the same procedure as for the driver side.
72551
6.REMOVE NO. 1 RECLINING HINGE COVER
Use the same procedure as for the driver side.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
72526
7.REMOVE RECLINING ADJUSTER RELEASE HANDLE
Use the same procedure as for the driver side.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
71848A
8.REMOVE SEAT ADJUSTER COVER CAP (w/ Vertical Adjuster)
Use the same procedure as for the driver side.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
71862
10.REMOVE FRONT SEAT INNER CUSHION SHIELD
72497B
11.REMOVE VERTICAL ADJUSTER BRACKET COVER (w/ Vertical Adjuster)
Use the same procedure as for the driver side.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
12.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Use the same procedure as for the driver side.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
13.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Use the same procedure as for the driver side.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY
82667D
14.REMOVE CONNECTOR HOLDER
71512S
15.REMOVE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)
| *A | for Standard Seat Type | *B | for Sports Seat Type |
| *a | Screwdriver | - | - |