Home › Vehicle Interior › SEAT BELT › FRONT SEAT INNER BELT ASSEMBLY › from 2021.07
RM3700E _58 Vehicle Interior _092991 SEAT BELT _0443756 FRONT SEAT INNER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT INNER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B620475N01
0.167,0.083 3.5,5.75 3.333,5.667 3.583,0.083 7.083,5.75 3.5,5.667 4.438,3.406 6.604,5.156 2.167,1.75 0.25,2.833 2.167,5.583 1.917,2.75 1.344,3.417 1.677,3.417 false 1.208,1.26 1.542,1.26 false 5.458,2.302 5.792,2.302 false 5.917,2.635 5.917,2.969 false 5.896,3.792 6.229,3.792 false 5.729,4.854 6.063,4.854 false 0.25,4.25 2.167,4.25 false 1.219,3.75 1.385,3.917 1.385,3.917 1.552,3.917 false 1.479,4.646 1.813,4.646 false 1.115,5.052 1.448,5.052 false 5.542,1.104 5.875,1.104 false 0.25,0.167 0.625,0.406 0.375,0.24 12 false *A 3.667,0.177 4.042,0.417 0.375,0.24 12 false *B 0.323,2.917 0.698,3.156 0.375,0.24 12 false *C 0.333,4.344 0.708,4.583 0.375,0.24 12 false *D 4.521,3.49 4.896,3.729 0.375,0.24 12 false *E 1.01,1.125 1.292,1.479 0.281,0.354 18 false 1 6.24,0.948 6.521,1.302 0.281,0.354 18 false 1 1.563,4.896 1.844,5.25 0.281,0.354 18 false 4 1.635,3.771 1.917,4.125 0.281,0.354 18 false 4 6.135,4.729 6.417,5.083 0.281,0.354 18 false 2 6.313,3.646 6.594,4 0.281,0.354 18 false 3 5.26,2.219 5.573,2.417 0.313,0.198 10 false *1 1.76,3.323 2.073,3.521 0.313,0.198 10 false *1 1.896,4.552 2.208,4.75 0.313,0.198 10 false *1 5.5,4.135 5.813,4.333 0.313,0.198 10 false x4 5.844,2.99 6.125,3.344 0.281,0.354 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT SEAT ASSEMBLY - (Click here) - -
2 FRONT SEAT CUSHION COVER 72925 - - -
3 NO. 2 FRONT SEAT UNDER TRAY RAIL SUB-ASSEMBLY 73508A - - -
4 FRONT SEAT INNER BELT ASSEMBLY 73230 - - -

*A for Driver Seat *B for Front Passenger Seat
*C for Manual Seat *D for Power Seat
*E w/ Under Tray - -
*1 FRONT SEAT BELT ANCHOR PLATE - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat inner belt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)

CAUTION:
B401522

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

If a front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad, separate type front seatback cover and front seatback pad with cover with the necessary parts in accordance with the extent of the collision damage.


HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system*1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD.

·

The following procedure is for LHD.

·

Use the same procedure for the driver seat and front passenger seat.

·

The procedure listed below is for the driver seat.



PROCEDURE

Hide 1.REMOVE FRONT SEAT ASSEMBLY

Z101186

·

for Manual Seat:

Click here(Click here)

·

for Power Seat:

Click here(Click here)



Hide 72925 2.REMOVE FRONT SEAT CUSHION COVER (w/ Under Tray)

Hide 73508A 3.REMOVE NO. 2 FRONT SEAT UNDER TRAY RAIL SUB-ASSEMBLY (w/ Under Tray)

Hide 73230 4.REMOVE FRONT SEAT INNER BELT ASSEMBLY

a.

for Driver Side Manual Seat:

B618033


b.

for Driver Side Power Seat:

B600108


c.

for Front Passenger Seat:

B622264