When the brake pedal is depressed, the stop light switch assembly outputs a signal to the ECM. The ECM uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control. When the ECM determines that terminals STP and ST1- of the stop light switch assembly are both less than 1 V, DTC P057162 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| P057162 | Brake Switch "A" Signal Compare Failure | When the ignition switch is ON and the dynamic radar cruise control system is operating, the ECM detects that the voltage at terminal STP and ST1- are both less than 1 V for approximately 0.5 seconds or more. | ·
Harness or connector ·
Stop light switch assembly ·
ECM |
Radar Cruise1 | A |
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the ECM, refer to Service Bulletin.
Pre-procedure1
Disconnect the A63 stop light switch assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A63)Location & Routingewd_type=routing;type=c;code=A63 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=2 |
||
| A63-2 (GND) - Body ground | Always | Below 1 Ω |
Procedure2
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A63)Location & Routingewd_type=routing;type=c;code=A63 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=7,6 |
||
| A63-7 (B) - Body ground | Always | 11 to 14 V |
| A63-6 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| A63-6 (B) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the A63 stop light switch assembly connector.
OK
NG
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the A54 ECM connector.
Disconnect the A63 stop light switch assembly connector.
Disconnect the A94*1 or A39*2 skid control ECU (brake actuator assembly) connector.
*1: for TMMF Made
*2: for TMC Made
Disconnect the H45 certification ECU (smart key ECU assembly) connector.*
*: w/ Entry and Start System
Disconnect the F19*1 or F20*2 shift lock control ECU (transmission floor shift assembly) connector.
*1: w/o Entry and Start System
*2: w/ Entry and Start System
Disconnect the D71 TCM connector.*
*: for CVT
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A54,A63)Location & Routingewd_type=routing;type=c,c;code=A54,A63 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=22,21 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=5,3 |
||
| A54-22 (ST1-) - A63-5 (L) | Always | Below 1 Ω |
| A54-21 (STP) - A63-3 (L) | Always | Below 1 Ω |
| A54-22 (ST1-) or A63-5 (L) - Body ground | Always | 10 kΩ or higher |
| A54-21 (STP) or A63-3 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the D71 TCM connector.
Connect the F19*1 or F20*2 shift lock control ECU (shift lock control unit assembly) connector.
*1: w/o Entry and Start System
*2: w/ Entry and Start System
Connect the H45 certification ECU (smart key ECU assembly) connector.*
*: w/ Entry and Start System
Connect theA94*1 or A39*2 skid control ECU (brake actuator assembly) connector.
*1: for TMMF Made
*2: for TMC Made
Connect the A63 stop light switch assembly connector.
Connect the A54 ECM connector.
OK
NG