Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › LANE TRACING ASSIST SYSTEM › from 2021.07
RM3700E _95 ADAS / AD _095278 ADVANCED DRIVER ASSISTANCE SYSTEM _0447904 LANE TRACING ASSIST SYSTEM C

ADVANCED DRIVER ASSISTANCE SYSTEM  LANE TRACING ASSIST SYSTEM  U023587  Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message  


DESCRIPTION

w/ Adaptive High Beam System:
·

The forward recognition camera is connected to the millimeter wave radar sensor assembly and headlight ECU sub-assembly LH via CAN communication. If communication with the millimeter wave radar sensor assembly stops, the forward recognition camera stores DTC U023587.


w/o Adaptive High Beam System:
·

The forward recognition camera is connected to the millimeter wave radar sensor assembly via CAN communication. If communication with the millimeter wave radar sensor assembly stops, the forward recognition camera stores DTC U023587.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
U023587 Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message When the ignition switch is ON for 3 seconds or more, a communication data malfunction between the forward recognition camera and the millimeter wave radar sensor assembly continues for approximately 2 seconds or more.
·

Wire harness and connector

·

Headlight ECU sub-assembly LH*

·

Forward Recognition Camera

·

Millimeter Wave Radar Sensor Assembly


Lane Control B

*: w/ Adaptive High Beam System


w/o Adaptive High Beam System
Pattern DTC output part name
(Display on GTS)
Suspected Area
(Malfunction Status)
Forward Recognition Camera Millimeter Wave Radar Sensor Assembly
Lane Control Forward Recognition Camera (Front Lighting Control) Pre-Collision System Radar Cruise2
U023587 U023587 U023A87 U023A87

○: DTC is output

-: DTC is not output

Pattern1 ○ ○ ○ ○ Harness or connector (Open or short)
Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)
Pattern2 ○ ○ - - Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)

w/ Adaptive High Beam System
Pattern DTC output part name
(Display on GTS)
Suspected Area
(Malfunction Status)
Forward Recognition Camera Millimeter Wave Radar Sensor Assembly Headlight ECU Sub-assembly LH
Lane Control Forward Recognition Camera (Front Lighting Control) Pre-Collision System Radar Cruise2 Headlight Control
U023587 U023587 U023A87 U023A87 U023A87

○: DTC is output

-: DTC is not output

Pattern1 ○ ○ ○ ○ ○ Harness or connector (Open or short)
Headlight ECU sub-assembly LH (Internal malfunction)
Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)
Pattern2 ○ ○ ○ ○ - Harness or connector (Open or short)
Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)
Pattern3 ○ ○ - - - Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)

HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.


WIRING DIAGRAM

w/o Adaptive High Beam System
C424985E02
4.594,1.021 4.906,1.219 0.313,0.198 10 false B8 4.583,1.198 7.156,1.448 2.573,0.25 10 false Millimeter Wave Radar Sensor Assembly 0.292,1.073 0.635,1.281 0.344,0.208 10 false V10 5.49,0.854 5.938,1 0.448,0.146 10 false CA1N 0.302,1.25 2.49,1.573 2.188,0.323 10 false Forward Recognition Camera 5.281,0.188 5.625,0.396 0.344,0.208 10 false 5 5.271,0.635 5.594,0.833 0.323,0.198 10 false 6 5.49,0.188 5.938,0.333 0.448,0.146 10 false CA1P 1,0.188 1.448,0.333 0.448,0.146 10 false CANH 1,0.833 1.448,0.979 0.448,0.146 10 false CANL 1.49,0.667 1.833,0.875 0.344,0.208 10 false 12 1.5,0.177 1.844,0.385 0.344,0.208 10 false 6

w/ Adaptive High Beam System
A438355E16
0.417,1.708 2.24,1.969 1.823,0.26 10 false Forward Recognition Camera 5.375,1.708 6.781,2.229 1.406,0.521 10 false Millimeter Wave Radar Sensor Assembly 0.385,3.656 3.208,4.031 2.823,0.375 10 false Headlight ECU Sub-assembly LH 1.167,0.594 1.781,0.792 0.615,0.198 10 false CANH 1.167,1.313 1.781,1.51 0.615,0.198 10 false CANL 5.688,0.594 6.302,0.792 0.615,0.198 10 false CA1P 5.698,1.302 6.313,1.5 0.615,0.198 10 false CA1N 1.26,2.698 1.719,2.896 0.458,0.198 10 false LCH 1.271,3.156 1.729,3.354 0.458,0.198 10 false LCL 0.427,1.552 1.042,1.75 0.615,0.198 10 false V10 1.677,0.583 1.854,0.813 0.177,0.229 10 false 6 1.656,1.052 1.917,1.24 0.26,0.188 10 false 12 0.396,3.49 1.01,3.688 0.615,0.198 10 false A110 1.677,2.542 1.938,2.729 0.26,0.188 10 false 22 1.677,3.031 1.938,3.219 0.26,0.188 10 false 21 5.375,1.552 5.99,1.75 0.615,0.198 10 false B8 5.417,0.573 5.594,0.802 0.177,0.229 10 false 5 5.417,1.052 5.594,1.281 0.177,0.229 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT


·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.

HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT


·

w/ Adaptive High Beam System:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>INITIALIZATION

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

If there are communication malfunctions for systems other than the forward recognition camera and millimeter wave radar sensor assembly, refer to "HOW TO PROCEED WITH TROUBLESHOOTING" for the CAN Communication System.

for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Adaptive High Beam System A
w/o Adaptive High Beam System B



A

2.CHECK FOR DTC

B

11.CHECK FOR DTC
2.CHECK FOR DTC
a.

Read each DTC and check the diagnosis pattern using the table below.

Chassis > Lane Control > Trouble Codes
50001 418
Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433
Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Powertrain > Radar Cruise2 > Trouble Codes
50001 426
Body Electrical > Headlight Control > Trouble Codes
50001 462

Pattern DTC output part name
(Display on GTS)
Lane Control Forward Recognition Camera (Front Lighting Control) Pre-Collision System Radar Cruise2 Headlight Control
Pattern 1 U023587 U023587 U023A87 U023A87 U023A87
Pattern 2 U023587 U023587 U023A87 U023A87 -
Pattern 3 U023587 U023587 - - -

Result:
Result Proceed to
Pattern 1 A
Pattern 2 B
Pattern 3 C



A

3.CLEAR DTC

B

8.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)

C

10.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
3.CLEAR DTC

Pre-procedure1

a.

Disconnect the A110 headlight ECU sub-assembly LH connector.


Procedure1

a.

Clear the DTCs.

Chassis > Lane Control > Clear DTCs
50002 418
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

4.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH
4.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



Procedure1

a.

Check for DTCs.

Chassis > Lane Control > Trouble Codes
50001 418
Result:
Result Proceed to
U023587 is not output A
U023587 is output B



Post-procedure1

a.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

5.CLEAR DTC
5.CLEAR DTC

Pre-procedure1

a.

Connect the A110 headlight ECU sub-assembly LH connector.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

a.

Clear the DTCs.

Chassis > Lane Control > Clear DTCs
50002 418
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

6.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY
6.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY

Pre-procedure1

a.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



Procedure1

a.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462

Result:
Result Proceed to
U023A87 is not output A
U023A87 is output B


Post-procedure1

a.

None



A

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

7.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)
7.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the V10 forward recognition camera connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V10)Location & Routing

Click Connector(V10)Body>No. 1 Roof Wire>Forward Recognition Camera

V10-6 (CANH) - V10-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
V10-6 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V10-12 (CANL) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V10-6 (CANH) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
V10-12 (CANL) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the V10 forward recognition camera connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V10)Location & Routing

Click Connector(V10)Body>No. 1 Roof Wire>Forward Recognition Camera

V10-6 (CANH) - V10-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
V10-6 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V10-12 (CANL) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V10-6 (CANH) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
V10-12 (CANL) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

9.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
9.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B8)Location & Routing

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

B8-5 (CA1P) - B8-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
B8-5 (CA1P) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B8-6 (CA1N) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B8-5 (CA1P) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
B8-6 (CA1N) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS SUB LINE OR CONNECTOR

10.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY

Pre-procedure1

a.

Disconnect the V10 forward recognition camera connector.


Procedure1

a.

Using an oscilloscope, check the waveform.

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(V10)Location & Routing

Click Connector(V10)Body>No. 1 Roof Wire>Forward Recognition Camera

V10-6 (CANH) - V10-12 (CANL) Ignition switch ON 1V/DIV., 100μs./DIV. Waveform generation


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

11.CHECK FOR DTC
a.

Read each DTC and check the diagnosis pattern using the table below.

Chassis > Lane Control > Trouble Codes
50001 418
Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433
Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Powertrain > Radar Cruise2 > Trouble Codes
50001 426

Pattern DTC output part name
(Display on GTS / Output DTC)
Lane Control Forward Recognition Camera (Front Lighting Control) Pre-Collision System Radar Cruise2
Pattern 1 U023587 U023587 U023A87 U023A87
Pattern 2 U023587 U023587 - -

Result:
Result Proceed to
Pattern 1 A
Pattern 2 B



A

12.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)

B

14.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
12.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the V10 forward recognition camera connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V10)Location & Routing

Click Connector(V10)Body>No. 1 Roof Wire>Forward Recognition Camera

V10-6 (CANH) - V10-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
V10-6 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V10-12 (CANL) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V10-6 (CANH) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
V10-12 (CANL) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

13.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
13.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B8)Location & Routing

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

B8-5 (CA1P) - B8-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
B8-5 (CA1P) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B8-6 (CA1N) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B8-5 (CA1P) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
B8-6 (CA1N) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS SUB LINE OR CONNECTOR

14.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY

Pre-procedure1

a.

Disconnect the V10 forward recognition camera connector.


Procedure1

a.

Using an oscilloscope, check the waveform.

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(V10)Location & Routing

Click Connector(V10)Body>No. 1 Roof Wire>Forward Recognition Camera

V10-6 (CANH) - V10-12 (CANL) Ignition switch ON 1V/DIV., 100μs./DIV. Waveform generation


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY