Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C05121F  Right Rear Wheel Speed Sensor Circuit Intermittent  


DESCRIPTION

Each speed sensor detects the wheel speed and sends the signals to the skid control ECU (brake booster with master cylinder assembly). These signals are used for ABS control.

HINT:

The output voltage values shown below are for when the vehicle wire harnesses are connected to the skid control ECU (brake booster with master cylinder assembly) and the speed sensors.


C269035E34
1.833,1.083 1.833,0.583 false 1.583,0.583 1.833,0.583 false 5,1.25 5,0.583 false 5,0.583 4.75,0.583 false 0.469,0.167 1.469,0.354 1,0.188 12 false for 2WD: 3.656,0.167 4.771,0.375 1.115,0.208 12 false for AWD: 0.656,0.469 1.729,0.667 1.073,0.198 10 false Speed Sensor 1.208,2.417 2.646,2.729 1.438,0.313 10 false Speed Sensor Rotor 4.833,3.385 5.448,3.583 0.615,0.198 10 false 1.4 V 4.833,3.75 5.448,3.948 0.615,0.198 10 false 0.7 V 3.677,4.156 4.552,4.563 0.875,0.406 10 false High Speed 2.76,4.156 3.573,4.625 0.813,0.469 10 false Low Speed 3.844,0.469 4.917,0.667 1.073,0.198 10 false Speed Sensor 4.573,2.448 6.01,2.76 1.438,0.313 10 false Speed Sensor Rotor

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C05121F Right Rear Wheel Speed Sensor Circuit Intermittent Any of the following is detected:
·

An open in the sensor signal of a malfunctioning wheel occurs 255 times or more.

·

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

·

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Rear speed sensor RH*1

·

Rear speed sensor RH (rear axle hub and bearing assembly RH)*2

·

Skid control sensor wire RH (No. 1 parking brake wire assembly)

·

Speed sensor installed improperly

·

Wire harness or connector

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)

·

Skid control ECU (brake booster with master cylinder assembly)


Brake/EPB A

*1: for AWD

*2: for 2WD


WIRING DIAGRAM

for AWD:
C436114E10
0.375,2.219 1.875,2.802 1.5,0.583 10 false Rear Speed Sensor RH 2.052,2.219 3.271,2.656 1.219,0.438 10 false Rear Skid Control Sensor Wire RH 5.083,3 5.542,3.198 0.458,0.198 10 false A38 5.052,3.146 7.156,3.5 2.104,0.354 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 1.469,1.135 1.719,1.344 0.25,0.208 10 false + 2.104,1.146 2.563,1.344 0.458,0.198 10 false RR+ 2.854,1.156 3.313,1.354 0.458,0.198 10 false RR+ 5.281,1.052 5.74,1.25 0.458,0.198 10 false RR+ 1.469,1.813 1.927,2.01 0.458,0.198 10 false - 2.083,1.813 2.542,2.01 0.458,0.198 10 false RR- 2.854,1.823 3.313,2.021 0.458,0.198 10 false RR- 5.292,1.708 5.75,1.906 0.458,0.198 10 false RR- 1.75,1.833 2.063,2.031 0.313,0.198 10 false u2 3.229,1.146 3.688,1.344 0.458,0.198 10 false u01 3.24,1.844 3.698,2.042 0.458,0.198 10 false u01 1.792,0.938 1.948,1.135 0.156,0.198 10 false 1 1.781,1.635 1.906,1.813 0.125,0.177 10 false 2 3.302,0.948 3.458,1.146 0.156,0.198 10 false 4 3.313,1.635 3.469,1.833 0.156,0.198 10 false 3 5.01,1.031 5.323,1.229 0.313,0.198 10 false 7 5.01,1.719 5.323,1.917 0.313,0.198 10 false 8 4.323,2.271 4.479,2.469 0.156,0.198 10 false * 0.208,3.396 1.896,3.594 1.688,0.198 10 false *: Shielded 1.74,1.146 2.052,1.344 0.313,0.198 10 false u2

for 2WD:
C436114E08
0.375,2.219 1.875,2.802 1.5,0.583 10 false Rear Speed Sensor RH (Rear Axle Hub and Bearing Assembly RH) 2.052,2.219 3.271,2.656 1.219,0.438 10 false Rear Skid Control Sensor Wire RH 5.083,3 5.542,3.198 0.458,0.198 10 false A38 5.052,3.146 7.156,3.5 2.104,0.354 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 1.469,1.135 1.719,1.344 0.25,0.208 10 false + 2.104,1.146 2.563,1.344 0.458,0.198 10 false RR+ 2.854,1.156 3.313,1.354 0.458,0.198 10 false RR+ 5.281,1.052 5.74,1.25 0.458,0.198 10 false RR+ 1.469,1.813 1.927,2.01 0.458,0.198 10 false - 2.083,1.813 2.542,2.01 0.458,0.198 10 false RR- 2.854,1.823 3.313,2.021 0.458,0.198 10 false RR- 5.292,1.708 5.75,1.906 0.458,0.198 10 false RR- 1.75,1.833 2.063,2.031 0.313,0.198 10 false u2 3.229,1.146 3.688,1.344 0.458,0.198 10 false u01 3.24,1.844 3.698,2.042 0.458,0.198 10 false u01 1.792,0.938 1.948,1.135 0.156,0.198 10 false 2 1.781,1.635 1.906,1.813 0.125,0.177 10 false 1 3.302,0.948 3.458,1.146 0.156,0.198 10 false 4 3.323,1.635 3.479,1.833 0.156,0.198 10 false 3 5.01,1.031 5.323,1.229 0.313,0.198 10 false 7 5.01,1.719 5.323,1.917 0.313,0.198 10 false 8 4.323,2.271 4.479,2.469 0.156,0.198 10 false * 0.208,3.396 1.896,3.594 1.688,0.198 10 false *: Shielded 1.74,1.146 2.052,1.344 0.313,0.198 10 false u2

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Chassis > Brake/EPB > Data List
Tester Display
RR Speed Sensor Voltage Open
50003 435 112

b.

Check for any momentary interruptions in the wire harness and connectors.

OK:

There are no momentary interruptions.


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (RR WHEEL SPEED)

NG

5.CHECK VEHICLE
2.READ VALUE USING GTS (RR WHEEL SPEED)
a.

Select the Data List on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
RR Wheel Speed
50003 435 15

b.

Check the rear speed sensor RH output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

6.CHECK REAR SPEED SENSOR RH INSTALLATION
3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Operate the GTS to read the DTCs.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C05121F is not output A
C05121F is output B



Post-procedure1

a.

None



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
for 2WD A
for AWD B



A

6.CHECK REAR SPEED SENSOR RH INSTALLATION

B

10.CHECK REAR SPEED SENSOR LH INSTALLATION
6.CHECK REAR SPEED SENSOR RH INSTALLATION

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.
C210569C19
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 false *a 2.344,1.698 2.656,1.896 0.313,0.198 10 false *b 1.344,0.104 1.656,0.302 0.313,0.198 10 false *c
*a Correct
*b Incorrect
*c No clearance


Check the rear speed sensor RH installation.

OK:

There is no clearance between the rear speed sensor RH and the rear axle hub and bearing assembly RH.


HINT:

The rear speed sensor rotor RH and rear speed sensor RH are incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor rotor RH needs to be replaced, replace the rear axle hub and bearing assembly RH with rear speed sensor RH.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

7.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

7.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the u2 and uO1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(u2,uO1)Location & Routing

Click Connector(u2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor RH (Rear Axle Hub & Bearing Assembly RH)

Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wire

u2-2 (+) - uO1-4 (RR+) Always Below 1 Ω
u2-2 (+) or uO1-4 (RR+) - Body ground and other terminals Always 10 kΩ or higher
u2-1 (-) - uO1-3 (RR-) Always Below 1 Ω
u2-1 (-) or uO1-3 (RR-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

8.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO1,A38)Location & Routing

Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wire

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

uO1-4 (RR+) - A38-7 (RR+) Always Below 1 Ω
uO1-4 (RR+) or A38-7 (RR+) - Body ground Always 10 kΩ or higher
uO1-3 (RR-) - A38-8 (RR-) Always Below 1 Ω
uO1-3 (RR-) or A38-8 (RR-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

9.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the uO1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure2

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(u2)Location & Routing

Click Connector(u2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor RH (Rear Axle Hub & Bearing Assembly RH)

u2-2 (+) - Body ground Ignition switch ON 8 to 14 V


HINT:

The rear speed sensor RH is incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor RH needs to be replaced, replace the rear axle hub and bearing assembly RH.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

10.CHECK REAR SPEED SENSOR LH INSTALLATION

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.
C168336C47
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Rear Speed Sensor RH
*a OK
*b NG
*c 8.5 N*m (87 kgf*cm, 75 in.*lbf)
*d No Clearance


Check the rear speed sensor RH installation.

OK:

There is no clearance between the sensor and the rear axle carrier.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

11.CHECK REAR SPEED SENSOR LH AND REAR SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

NG

11.CHECK REAR SPEED SENSOR LH AND REAR SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

Pre-procedure1

a.

Remove the rear speed sensor RH and the component with the rear speed sensor rotor RH.

HINT:

for Rear Speed Sensor RH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR (for 2WD)>REMOVAL

for Rear Speed Sensor Rotor RH: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for 2WD)>REMOVAL



Procedure1

a.

Check the rear speed sensor tip RH and rear speed sensor rotor RH.

OK:

The rear speed sensor tip RH and rear speed sensor rotor RH are free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the rear speed sensor RH, clean the rear speed sensor RH and then check the rear speed sensor rotor RH.

·

If the rear speed sensor RH is damaged, replace the rear speed sensor RH with a new one.



Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

12.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY

NG

CLEAN OR REPLACE REAR SPEED SENSOR LH AND REAR SPEED SENSOR ROTOR LH

12.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the u2 and uO1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(u2,uO1)Location & Routing

Click Connector(u2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor RH (Rear Axle Hub & Bearing Assembly RH)

Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wire

u2-1 (+) - uO1-4 (RR+) Always Below 1 Ω
u2-1 (+) or uO1-4 (RR+) - Body ground and other terminals Always 10 kΩ or higher
u2-2 (-) - uO1-3 (RR-) Always Below 1 Ω
u2-2 (-) or uO1-3 (RR-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

13.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO1,A38)Location & Routing

Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wire

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

uO1-4 (RR+) - A38-7 (RR+) Always Below 1 Ω
uO1-4 (RR+) or A38-7 (RR+) - Body ground Always 10 kΩ or higher
uO1-3 (RR-) - A38-8 (RR-) Always Below 1 Ω
uO1-3 (RR-) or A38-8 (RR-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

14.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the uO1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure2

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(u2)Location & Routing

Click Connector(u2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor RH (Rear Axle Hub & Bearing Assembly RH)

u2-1 (+) - Body ground Ignition switch ON 8 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY