Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C059400  Brake Booster Motor "A" Performance  C121B14  Brake Booster Motor "A" Control "A" Circuit Short to Ground or Open  C126A14  Brake Booster Motor "A" Control "B" Circuit Short to Ground or Open  C141C12  Brake Booster Motor "A" Control Circuit Short to Battery  C141C14  Brake Booster Motor "A" Control Circuit Short to Ground or Open  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) detects decreases in the accumulator pressure according to the data from the accumulator pressure sensor, and then starts and stops the pump motor by operating the motor relay.

HINT:

If the auxiliary battery voltage is temporarily low, these DTCs may be stored.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C059400 Brake Booster Motor "A" Performance The pump motor is operating continuously for 178 seconds or more. (When the relay is malfunctioning for 98 seconds or more.)
·

Short in pump motor circuit or pump motor monitor circuit

·

Motor relay stuck

·

Accumulator pressure sensor malfunction

·

Skid control ECU (brake booster with master cylinder assembly)


Brake/EPB A
C121B14 Brake Booster Motor "A" Control "A" Circuit Short to Ground or Open An open is detected in the motor relay drive circuit for 0.2 seconds or more.
·

Open in pump motor circuit or pump motor monitor circuit

·

Skid control ECU (brake booster with master cylinder assembly)


Brake/EPB A
C126A14 Brake Booster Motor "A" Control "B" Circuit Short to Ground or Open An open is detected in the motor relay drive circuit for 0.2 seconds or more.
·

Open in pump motor circuit or pump motor monitor circuit

·

Skid control ECU (brake booster with master cylinder assembly)


Brake/EPB A
C141C12 Brake Booster Motor "A" Control Circuit Short to Battery A short is detected in the motor relay drive circuit for 2 seconds or more.
·

Short in pump motor circuit or pump motor monitor circuit

·

Skid control ECU (brake booster with master cylinder assembly)


Brake/EPB A
C141C14 Brake Booster Motor "A" Control Circuit Short to Ground or Open An open is detected in the motor relay drive circuit for 0.2 seconds or more.
·

Open in pump motor circuit or pump motor monitor circuit

·

Skid control ECU (brake booster with master cylinder assembly)


Brake/EPB A

WIRING DIAGRAM

C345755E30
4.75,5.333 5.208,5.531 0.458,0.198 10 false A38 4.75,5.531 6.813,5.927 2.063,0.396 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.146,7.323 6.542,7.583 1.396,0.26 10 false from Auxiliary Battery 3.281,4.688 4.375,4.927 1.094,0.24 10 false ABS MTR NO. 2 3.271,3.854 4.354,4.063 1.083,0.208 10 false ABS MTR NO. 1 4.406,3.573 4.865,3.771 0.458,0.198 10 false 2 4.333,4.406 4.792,4.604 0.458,0.198 10 false 28 4.615,3.802 5.073,4 0.458,0.198 10 false MRI1 4.604,4.635 5.063,4.833 0.458,0.198 10 false MRI2 4.917,2.344 5.302,2.729 0.385,0.385 10 false Motor Relay 6.406,2.094 6.865,2.292 0.458,0.198 10 false IC 4.333,1.354 4.792,1.552 0.458,0.198 10 false 27 4.604,1.594 5.063,1.792 0.458,0.198 10 false MRO2 4.406,0.521 4.865,0.719 0.458,0.198 10 false 1 4.615,0.75 5.073,0.948 0.458,0.198 10 false MRO1 1.146,0.75 1.604,0.948 0.458,0.198 10 false BM1 1.552,0.521 2.01,0.719 0.458,0.198 10 false 2 1.135,1.604 1.594,1.802 0.458,0.198 10 false BM2 1.063,6.115 1.521,6.313 0.458,0.198 10 false GND1 1.552,5.854 2.01,6.052 0.458,0.198 10 false 4 1.052,7.063 1.51,7.26 0.458,0.198 10 false GND2 1.552,6.813 2.01,7.01 0.458,0.198 10 false 3 1.563,1.344 2.021,1.542 0.458,0.198 10 false 1 0.177,7.99 0.635,8.188 0.458,0.198 10 false A30 0.167,8.167 1.49,8.552 1.323,0.385 10 false Brake Booster Pump Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY



PROCEDURE

1.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C059400, C121B14, C126A14, C141C12 or C141C14 is output A
C059400, C121B14, C126A14, C141C12 or C141C14 and other DTCs are output B




A

2.READ VALUE USING GTS (MTT)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.READ VALUE USING GTS (MTT)
a.

Select the Data List on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MTT Pump motor operation status OFF / ON OFF: Pump motor off
ON: Pump motor on
-
Chassis > Brake/EPB > Data List
Tester Display
MTT
50003 435 100

b.

Depress the brake pedal several times and check the operation status of the MTT.

HINT:

Depressing the brake pedal several times drops the accumulator pressure and operates the pump motor.



Result:
Result Proceed to
The MTT in the Data List turns on or off by depressing the brake pedal several times. A
The status of MTT in the Data List does not change even after depressing the brake pedal several times. B



A

3.INSPECT BRAKE BOOSTER PUMP ASSEMBLY

B

9.CHECK HARNESS AND CONNECTOR (MRI TERMINAL)
3.INSPECT BRAKE BOOSTER PUMP ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the brake booster pump assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.
C345125C35
0.698,1.333 1.448,1.656 true 1.99,1.604 2.74,1.302 true 2.01,2.125 2.719,2.656 true 0.729,2.625 1.427,2.135 true 0.208,0.198 0.521,0.396 0.313,0.198 10 false *a 0.385,1.229 0.698,1.427 0.313,0.198 10 false BM1 0.323,2.563 0.75,2.792 0.427,0.229 10 false GND1 2.75,2.594 3.188,2.854 0.438,0.26 10 false GND2 2.792,1.188 3.188,1.406 0.396,0.219 10 false BM2
*a Component without harness connected
(Brake Booster Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (BM1) - 4 (GND1) Always 10 Ω or less
1 (BM2) - 3 (GND2) Always 10 Ω or less
2 (BM1) - 1 (BM2) Always Below 1 Ω
4 (GND1) - 3 (GND2) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A30)Location & Routing

Click Connector(A30)Engine Compartment>Engine Room Main Wire>Brake Booster Pump Assembly

A30-4 (GND1) - Body ground Always Below 1 Ω
A30-3 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (ACCUMULATOR PRESSURE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

5.READ VALUE USING GTS (ACCUMULATOR PRESSURE)
a.

Reconnect the A30 brake booster pump assembly connector.


b.

Disconnect the A27 brake pedal stroke sensor assembly connector.


c.

Select the Data List on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MTT Pump motor operation status OFF / ON OFF: Pump motor off
ON: Pump motor on
-
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa, Max.: 24.48 MPa 15.00 to 21.00 MPa
(Pressure stable and pump motor stopped)
When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > Brake/EPB > Data List
Tester Display
MTT
Accumulator Pressure
50003 435 100,212

d.

Depress the brake pedal several times to operate the pump motor, then wait until it stops.


e.

After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.

HINT:
·

This inspection checks whether an accumulator pressure sensor malfunction, internal brake actuator (brake booster with master cylinder assembly) leak or prolonged operation due to detection of low pressure caused by accumulator deterioration, caused the DTC to be stored.

·

If the brake fluid level in the brake master cylinder reservoir assembly (brake booster with master cylinder assembly) drops, an external brake fluid leak is suspected.




Result:
Result Proceed to
30 seconds after the pump motor stops the drop in the value of Accumulator Pressure after the pump motor stops is less than 2.50 MPa and pump motor does not operate within 30 seconds A
30 seconds after the pump motor stops the drop in the value of Accumulator Pressure is 2.50 MPa or more or pump motor operates within 30 seconds B



A

6.CLEAR DTC

B

8.READ VALUE USING GTS (SERVO PRESSURE)
6.CLEAR DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the A27 brake pedal stroke sensor assembly connector.


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

7.RECONFIRM DTC
7.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C059400, C121B14, C126A14, C141C12 and C141C14 are not output A
C059400, C121B14, C126A14, C141C12 or C141C14 is output B



Post-procedure1

a.

None



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

8.READ VALUE USING GTS (SERVO PRESSURE)
a.

Turn the ignition switch off.


b.

Reconnect the A27 brake pedal stroke sensor assembly connector.


c.

Select the Active Test on the GTS.

Chassis > Brake/EPB > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Solenoid (SLR) Linear solenoid reduction valve (SLR) Solenoid ON/OFF ECB: Electronically Controlled Brake System
Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal released: 0.00 to 1.53 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > Brake/EPB > Active Test
Active Test Display
ECB Solenoid (SLR)
Data List Display
Servo Pressure
50004 435 42 210

d.

Perform the Active Test and operate the linear solenoid (SLR) in the brake actuator (brake booster with master cylinder assembly).


e.

Check that the servo pressure output value does not increase when performing the Active Test.

OK:

The servo pressure output value does not increase when performing the Active Test.


HINT:

If the servo pressure output value increases, an internal brake fluid leak in the brake actuator (brake booster with master cylinder assembly) is suspected.



Result:
Result Proceed to
The servo pressure output value increases. A
The servo pressure output value does not increase. B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (MRI TERMINAL)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A38)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

A38-2 (MRI1) - Body ground Always 11 to 14 V
A38-28 (MRI2) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MRI CIRCUIT)

10.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE BOOSTER PUMP ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A30 brake booster pump assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A38,A30)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

Click Connector(A30)Engine Compartment>Engine Room Main Wire>Brake Booster Pump Assembly

A38-1 (MRO1) - A30-2 (BM1) Always Below 1 Ω
A38-1 (MRO1) or A30-2 (BM1) - Body ground Always 10 kΩ or higher
A38-27 (MRO2) - A30-1 (BM2) Always Below 1 Ω
A38-27 (MRO2) or A30-1 (BM2) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR