Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C134951  Pressure Holding Solenoid Valve Learning Not Programmed  C134954  Pressure Holding Solenoid Valve Learning Missing Calibration  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) stores the individual characteristic of each holding solenoid built into the brake actuator assembly. Based on the stored information, the skid control ECU (brake booster with master cylinder assembly) calibrates the individual differences and controls systems.

The skid control ECU (brake booster with master cylinder assembly) receives the park (P) signal from the hybrid vehicle control ECU through the CAN communication system.

These DTCs are cleared when the ABS holding solenoid valve learning results are normal.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C134951 Pressure Holding Solenoid Valve Learning Not Programmed The ABS holding solenoid valve learning value is not stored. Perform ABS holding solenoid valve learning and check for DTCs. If no DTCs are output again, the valve is normal. Brake/EPB A
C134954 Pressure Holding Solenoid Valve Learning Missing Calibration The ABS holding solenoid valve learning value cannot be obtained.
·

Perform ABS holding solenoid valve learning and check for DTCs. If no DTCs are output again, the valve is normal.

·

Skid control ECU (brake booster with master cylinder assembly)

·

Brake actuator assembly


Brake/EPB A

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY


HINT:

Before performing linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization, DTC C124A00 will be output.


PROCEDURE

1.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Check that DTCs other than C134951 and C134954 are not output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
Only C134951 or C134954 is output A
None of the above conditions are met B



A

3.PERFORM AIR BLEEDING

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.PERFORM AIR BLEEDING

NEXT

4.PERFORM ABS HOLDING SOLENOID VALVE LEARNING
4.PERFORM ABS HOLDING SOLENOID VALVE LEARNING
a.

Turn the ignition switch off.


b.

Check and ensure the following conditions required for performing ABS holding solenoid valve learning and then perform ABS holding solenoid valve learning.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY


Chassis > Brake/EPB > Utility
Tester Display
ECB Utility
50005 435 2617
1.

The auxiliary battery voltage is 11 to 15.5 V when the ignition switch ON (READY).

2.

The brake actuator assembly is not hot.

3.

The hybrid control system is not malfunctioning.

4.

The shift state indicator shows that the vehicle shift state is park (P).

5.

The READY light in the combination meter assembly is illuminated.

6.

The brake pedal is not depressed.

7.

The parking brake is released.


NOTICE:

Learning will be performed in the order of linear solenoid valve offset learning and then ABS holding solenoid valve learning.



Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C134951 and C134954 are not output A
C134951 or C134954 is output B



Post-procedure1

a.

None



A

END

B

7.PERFORM ACTIVE TEST USING GTS (ABS SOLENOID)
7.PERFORM ACTIVE TEST USING GTS (ABS SOLENOID)
a.

Select the Active Test on the GTS.

Chassis > Brake/EPB > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
ABS Solenoid Pressure holding solenoid (SFRH, SFLH, SRRH, SRLH)
Pressure reduction solenoid (SFRR, SFLR, SRRR, SRLR)
Solenoid Start (Activate)
Solenoid SFRH / SFLH / SRRH / SRLH / SFRR / SFLR / SRRR / SRLR
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P or N

·

Apply the parking brake


HINT:

To protect actuator and Solenoid(s), this test will continue for 25 seconds.


Check that the GTS display for the solenoid (SRLR, SRLH, SRRR, SRRH, SFLR, SFLH, SFRR or SFRH) changes to ON/OFF during Solenoid Start (Activate)
Chassis > Brake/EPB > Active Test
Tester Display
ABS Solenoid
50004 435 42001

b.

Operate the SFRH (front right wheel holding solenoid valve), SFLH (front left wheel holding solenoid valve), SRRH (rear right wheel holding solenoid valve) and SRLH (rear left wheel holding solenoid valve) solenoids one by one. While operating each solenoid, depress the brake pedal, open the corresponding bleeder plug and check that brake fluid does not flow from the bleeder plug.

OK:

Brake fluid does not flow from the corresponding bleeder plug when the brake pedal is depressed when operating each solenoid.



c.

While not operating the SFRH (front right wheel holding solenoid valve), SFLH (front left wheel holding solenoid valve), SRRH (rear right wheel holding solenoid valve) and SRLH (rear left wheel holding solenoid valve) solenoids, depress the brake pedal, open each bleeder plug and check that brake fluid flows from each bleeder plug.

OK:

Brake fluid flows from each bleeder plug when not operating each solenoid and the brake pedal is depressed.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG