This DTC is stored if internal or external brake fluid leaks are detected due to improper sealing in the brake actuator (brake booster with master cylinder assembly) or brake booster pump assembly. Internal leaks are suspected if the pump motor operates frequently without braking.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C139100 | Abnormal Leak in Accumulator | Any of the following is detected:
·
When the brake pedal is not depressed and the pump motor is operating, the accumulator pressure sensor value does not increase a certain number of times. ·
When the brake pedal is not depressed and the pump motor is not operating, the accumulator pressure sensor decrease rate exceeds a certain threshold a certain number of times. |
·
Brake fluid leaks ·
Brake actuator (brake booster with master cylinder assembly) (Malfunctioning internal seal etc.) ·
Brake booster pump assembly (Accumulator internal gas pressure decrease, etc.) |
Brake/EPB | A |
After replacing the brake actuator (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Select the Active Test on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| ECB Solenoid (SLR) | Linear solenoid reduction valve (SLR) | Solenoid ON/OFF | ECB: Electronically Controlled Brake System |
| Tester Display |
|---|
| ECB Solenoid (SLR) |
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Servo Pressure | Pressure value of servo | Min.: 0.00 MPa, Max.: 24.48 MPa | Brake pedal released: 0.00 to 1.53 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
| Tester Display |
|---|
| Servo Pressure |
Perform the Active Test and operate the linear solenoid (SLR) in the brake actuator (brake booster with master cylinder assembly).
Check that the servo pressure output value does not increase when performing the Active Test.
The servo pressure output value does not increase when performing the Active Test.
If the servo pressure output value increases, an internal brake fluid leak in the brake actuator (brake booster with master cylinder assembly) is suspected.
| Result | Proceed to |
|---|---|
| The servo pressure output value increases. | A |
| The servo pressure output value does not increase. | B |
A
B
Turn the ignition switch to ON (READY).
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| MTT | Pump motor operation status | OFF / ON | OFF: Pump motor off
ON: Pump motor on |
- |
| Tester Display |
|---|
| MTT |
With the ignition switch ON (READY), check the operation of the pump motor.
The pump motor operates once or more within 20 seconds or operates for 10 seconds or more each time.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that there are no leaks from the connections between the brake booster pump assembly and brake booster with master cylinder assembly.
As a visual check is very difficult, perform the check with the following procedure.
Bleed the air from the brake system.
Turn the ignition switch off.
Disconnect the A27 brake pedal stroke sensor assembly connector.
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| MTT | Pump motor operation status | OFF / ON | OFF: Pump motor off
ON: Pump motor on |
- |
| Accumulator Pressure | Accumulator pressure output value | Min.: 0.00 MPa, Max.: 24.48 MPa | 15.00 to 21.00 MPa
(Pressure stable and pump motor stopped) |
When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator |
| Tester Display |
|---|
| MTT |
| Accumulator Pressure |
Depress the brake pedal several times to operate the pump motor, then wait until it stops.
After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.
| Result | Proceed to |
|---|---|
| 30 seconds after the pump motor stops the drop in the value of Accumulator Pressure after the pump motor stops is less than 2.50 MPa and pump motor does not operate within 30 seconds | A |
| 30 seconds after the pump motor stops the drop in the value of Accumulator Pressure is 2.50 MPa or more or pump motor operates within 30 seconds | B |
A
for Brake Booster with Master Cylinder Assembly: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model TMC Made RHD)>REMOVAL
for the brake booster pump assembly: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER PUMP>REMOVAL
B