Refer to DTCs C05061F.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C14E314 | Right Front Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open | Any of the following is detected:
·
The speed sensor power source voltage is low for 0.5 seconds or more. ·
The speed sensor power source voltage is low for 0.2 seconds, and does not return to normal for 60 seconds or more. |
·
Front speed sensor RH ·
Wire harness or connector ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake/EPB | A |
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Speed Open | Front speed sensor RH open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Tester Display |
|---|
| FR Speed Open |
Check for any momentary interruptions in the wire harness and connectors.
Perform the above inspection before removing the sensor and connector.
| Result | Proceed to |
|---|---|
| The value of FR Speed Open is always Normal | A |
| The value of FR Speed Open outputs Error one or more times | B |
A
B
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front speed sensor RH | Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FR Wheel Speed |
Check the front speed sensor RH output value.
The output value changes in accordance with the vehicle speed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Procedure1
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C14E314 is not output | A |
| C14E314 is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the A23 front speed sensor RH connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A38,A23)Location & Routingewd_type=routing;type=c,c;code=A38,A23 Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assemblyewd_type=component;type=c;code=A38;pinno=3,4 Click Connector(A23)Engine Compartment>Engine Room Main Wire>Front Speed Sensor RHewd_type=component;type=c;code=A23;pinno=1,2 |
||
| A38-3 (FR+) - A23-1 (FR+) | Always | Below 1 Ω |
| A38-3 (FR+) or A23-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| A38-4 (FR-) - A23-2 (FR-) | Always | Below 1 Ω |
| A38-4 (FR-) or A23-2 (FR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A23)Location & Routingewd_type=routing;type=c;code=A23 Click Connector(A23)Engine Compartment>Engine Room Main Wire>Front Speed Sensor RHewd_type=component;type=c;code=A23;pinno=1 |
||
| A23-1 (FR+) - Body ground | Ignition switch ON | 8 to 14 V |
Check the front speed sensor RH signal after replacement.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG