Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  VSC does not Operate or VSC does not Operate Correctly  


DESCRIPTION

When ABS, TRC or VSC is operating, the skid control ECU (brake booster with master cylinder assembly) blinks the slip indicator light to inform the driver that slippage occurred.

When a communication malfunction with the hybrid vehicle control ECU is detected, TRC and VSC are disabled. Also, TRC and VSC are disabled when a DTC is stored.

CAUTION / NOTICE / HINT

NOTICE:

After replacing or reinstalling the yaw rate sensor, perform "Calibration" after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY


PROCEDURE

1.BRAKE PROBLEM CHECK
a.

Check whether the slip indicator light was illuminated when VSC did not operate.

OK:

The slip indicator light was illuminated.


HINT:

When a DTC is stored, the slip indicator light is illuminated and VSC does not operate due to the fail-safe function.



b.

Check whether the vehicle speed was 15 km/h (9 mph) or less when VSC did not operate.

OK:

The vehicle speed was 15 km/h (9 mph) or less.


HINT:

VSC does not operate when the vehicle speed is 15 km/h (9 mph) or less.



c.

Check whether the vehicle was driven straight for a few seconds at 35 km/h (22 mph) or more.

OK:

The vehicle was not driven straight for a few seconds at 35 km/h (22 mph) or more.


HINT:

When the ignition switch is turned ON, as steering sensor zero point calibration is not performed below 35 km/h (22 mph), VSC will not operate until the vehicle is driven straight for a few seconds at 35 km/h (22 mph) or more.



Result:
Proceed to
OK
NG



OK

END

NG

2.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Check the DTCs (electronically controlled brake system) that are output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are not output A
Any Electronically Controlled Brake System DTCs are output B



A

4.CHECK TIRES

B

4.CHECK TIRES
a.

Check that the tire of each wheel is the correct size.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION

OK:

The tire of each wheel is the correct size.



Result:
Proceed to
OK
NG



OK

5.CHECK AIR BAG SENSOR ASSEMBLY INSTALLATION

NG

REPLACE THE TIRE OF EACH WHEEL WITH THE CORRECT SIZE

5.CHECK AIR BAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag sensor assembly) is not tilted.



Result:
Proceed to
OK
NG



OK

NG