Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484413 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C050014  Left Front Wheel Speed Sensor Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC C05001F.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>C05001F

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C050014 Left Front Wheel Speed Sensor Circuit Short to Ground or Open An open in the speed sensor signal circuit continues for 0.5 seconds or more.
·

Front speed sensor LH

·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


Brake/EPB A

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS (FL SPEED OPEN)

Pre-procedure1

a.

Select the line graph display on the GTS.


Procedure1

a.

Check for any momentary interruption in the wire harness and connector.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Speed Open Front speed sensor LH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Chassis > Brake/EPB > Data List
Tester Display
FL Speed Open
50003 435 102
OK:

Normal (There are no momentary interruptions.)


NOTICE:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.READ VALUE USING GTS (FL WHEEL SPEED)

NG

5.INSPECT HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)
2.READ VALUE USING GTS (FL WHEEL SPEED)

Pre-procedure1

a.

Drive the vehicle and perform a road test.


Procedure1

a.

Check the speed value output from the speed sensor displayed on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
FL Wheel Speed
50003 435 14
HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CLEAR DTC

NG

5.INSPECT HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)
3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Operate the GTS to clear the codes.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Operate the GTS to read the DTCs.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C050014 is not output A
C050014 is output B



Post-procedure1

a.

None



A

B

5.INSPECT HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A22 front speed sensor LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A22,A94)Location & Routing

Click Connector(A22)Engine Compartment>Engine Room Main Wire>Front Speed Sensor LH

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A22-1 (FL+) - A94-22 (FL+) Always Below 1 Ω
A22-1 (FL+) or A94-22 (FL+) - Body ground Always 10 kΩ or higher
A22-2 (FL-) - A94-21 (FL-) Always Below 1 Ω
A22-2 (FL-) or A94-21 (FL-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Reconnect the A94 skid control ECU (brake actuator assembly) connector.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A22)Location & Routing

Click Connector(A22)Engine Compartment>Engine Room Main Wire>Front Speed Sensor LH

A22-1 (FL+) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG