Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484413 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C05001F  Left Front Wheel Speed Sensor Circuit Intermittent  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C235852E10
1.073,0.865 1.448,0.865 1.448,0.865 1.448,1.073 false 6.458,0.979 6.958,1.146 0.5,0.167 10 false 1.4 V 6.458,1.323 6.969,1.479 0.51,0.156 10 false 0.7 V 0.146,0.771 1.167,1.104 1.021,0.333 10 false Speed Sensor 4.469,1.792 5.396,2.021 0.927,0.229 10 false Low speed 5.375,1.792 6.49,2.104 1.115,0.313 10 false High speed 1.115,2.125 2.74,2.479 1.625,0.354 10 false Speed Sensor Rotor

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C05001F Left Front Wheel Speed Sensor Circuit Intermittent Any of the following is detected:
·

When the +BS terminal voltage is 17.4 V or less, an open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Front speed sensor LH

·

Speed sensor installation

·

Wire harness and connector

·

Front speed sensor rotor LH (front axle hub sub-assembly LH)

·

Skid control ECU (brake actuator assembly)


Brake/EPB A

WIRING DIAGRAM

C400496E52
5.26,1.031 5.76,1.198 0.5,0.167 10 false FL+ 1.667,1.167 2.104,1.333 0.438,0.167 10 false FL+ 1.667,1.833 2.104,2.021 0.438,0.188 10 false FL- 5.271,1.719 5.729,1.917 0.458,0.198 10 false FL- 4.917,2.938 5.417,3.135 0.5,0.198 10 false A94 4.917,3.104 7.073,3.594 2.156,0.49 10 false Skid Control ECU (Brake Actuator Assembly) 4.979,1.01 5.313,1.26 0.333,0.25 10 false 22 4.979,1.688 5.292,2 0.313,0.313 10 false 21 2.021,1.688 2.406,1.958 0.385,0.271 10 false 2 2.021,1.021 2.375,1.292 0.354,0.271 10 false 1 0.75,2.417 2.417,2.667 1.667,0.25 10 false Front Speed Sensor LH 0.75,2.25 1.219,2.448 0.469,0.198 10 false A22

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>TEST MODE PROCEDURE

·

After replacing or removing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS (FL SPEED SENSOR VOLTAGE OPEN)

Pre-procedure1

a.

Select the line graph display on the GTS.


Procedure1

a.

Check for any momentary interruption in the wire harness and connector.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Chassis > Brake/EPB > Data List
Tester Display
FL Speed Sensor Voltage Open
50003 435 111
OK:

Normal (There are no momentary interruptions.)


NOTICE:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.READ VALUE USING GTS (FL WHEEL SPEED)

NG

5.CHECK FRONT SPEED SENSOR LH INSTALLATION
2.READ VALUE USING GTS (FL WHEEL SPEED)

Pre-procedure1

a.

Drive the vehicle and perform a road test.


Procedure1

a.

Check the speed value output from the speed sensor displayed on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
FL Wheel Speed
50003 435 14
HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CLEAR DTC

NG

5.CHECK FRONT SPEED SENSOR LH INSTALLATION
3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Operate the GTS to clear the codes.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Operate the GTS to read the DTCs.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C05001F is not output A
C05001F is output B



Post-procedure1

a.

None



A

B

5.CHECK FRONT SPEED SENSOR LH INSTALLATION

Pre-procedure1

a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor LH
*a Correct
*b Incorrect
*c 8.5 Nm
*d No clearance


Turn the ignition switch off.


Procedure1

a.

Check the front speed sensor LH installation.

OK:

There is no clearance between the front speed sensor LH and steering knuckle.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.CHECK FRONT SPEED SENSOR LH AND FRONT SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR LH

6.CHECK FRONT SPEED SENSOR LH AND FRONT SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)

Pre-procedure1

a.

Remove the front speed sensor LH and the component with the front speed sensor rotor LH.

HINT:

for front speed sensor LH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

for front speed sensor rotor LH: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL



Procedure1

a.

Check the front speed sensor LH tip and front speed sensor rotor LH.

OK:

No scratches, oil, or foreign matter on the front speed sensor LH tip and front speed sensor rotor LH.


NOTICE:
·

If there is oil or foreign matter on the front speed sensor LH, clean the front speed sensor LH.

·

If the front speed sensor LH is damaged, replace the front speed sensor LH with a new one.

·

Do not use parts cleaner when cleaning the front speed sensor rotor LH.

·

If the front speed sensor rotor LH is damaged, replace the front speed sensor rotor LH with a new one.



HINT:
·

The front speed sensor rotor LH is incorporated into the front axle hub sub-assembly LH.

·

If the front speed sensor rotor LH needs to be replaced, replace it together with the front axle hub sub-assembly LH.



Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

7.INSPECT HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR LH OR COMPONENT WITH FRONT SPEED SENSOR ROTOR LH

7.INSPECT HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A22 front speed sensor LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A22,A94)Location & Routing

Click Connector(A22)Engine Compartment>Engine Room Main Wire>Front Speed Sensor LH

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A22-1 (FL+) - A94-22 (FL+) Always Below 1 Ω
A22-1 (FL+) or A94-22 (FL+) - Body ground Always 10 kΩ or higher
A22-2 (FL-) - A94-21 (FL-) Always Below 1 Ω
A22-2 (FL-) or A94-21 (FL-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

8.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Reconnect the A94 skid control ECU (brake actuator assembly) connector.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure2

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A22)Location & Routing

Click Connector(A22)Engine Compartment>Engine Room Main Wire>Front Speed Sensor LH

A22-1 (FL+) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG