Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › from 2021.07
RM3700E _52 Drivetrain _093736 AXLE AND DIFFERENTIAL _0441810 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C462332N01
0.979,1.688 0.833,1.031 0.833,1.031 0.667,1.031 false 3.427,1.083 3.594,0.719 3.594,0.719 3.771,0.719 false 4.708,1.333 5.146,1.333 false 6.094,1.625 6.396,1.625 false 3.677,2.458 3.979,2.458 false 6.49,0.208 6.76,0.208 false 1.646,2.771 2.01,2.771 false 1.354,4.375 1.688,4.375 false 4.167,4.906 4.469,4.906 false 4.229,3.688 4.521,2.917 4.521,2.917 4.688,2.917 false 3.302,2.208 3.604,2.208 false 3.135,3.854 3.135,4.26 false 0.563,4.302 0.563,4.677 false 0.375,0.906 0.656,1.26 0.281,0.354 18 false 11 0.625,4.677 0.917,4.969 0.292,0.292 18 false 8 1.042,4.24 1.448,4.573 0.406,0.333 18 false 10 3.188,4.281 3.51,4.583 0.323,0.302 18 false 9 3.99,4.771 4.344,5.146 0.354,0.375 18 false 3 5.125,2.771 5.417,3.073 0.292,0.302 18 false 4 3.177,2.115 3.479,2.344 0.302,0.229 10 false ● 0.219,3.313 0.521,3.542 0.302,0.229 10 false x2 1.479,1.375 1.781,1.604 0.302,0.229 10 false x2 2.708,1.26 3.01,1.49 0.302,0.229 10 false x2 1.323,2.635 1.604,2.99 0.281,0.354 18 false 12 4.073,0.583 4.354,0.938 0.281,0.354 18 false 7 5.396,1.198 5.75,1.51 0.354,0.313 18 false 5 6.438,1.531 6.74,1.76 0.302,0.229 10 false *1 4.99,2.813 5.229,3.083 0.24,0.271 10 false ● 5.427,0.125 5.708,0.417 0.281,0.292 18 false 1 2.417,4.958 2.719,5.188 0.302,0.229 10 false x2 6.167,0.146 6.583,0.417 0.417,0.271 12 false (*A) 5.573,0.156 5.969,0.396 0.396,0.24 12 false (*A) 4.052,2.323 4.313,2.656 0.26,0.333 18 false 6 4.229,2.365 4.667,2.615 0.438,0.25 12 false (*B) 5.854,0.115 6.281,0.417 0.427,0.302 18 false , 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - (Click here) - -
3 FRONT WHEEL - - - -
4 FRONT AXLE SHAFT NUT 43502H (Click here) - -
5 FRONT SPEED SENSOR 89543 (Click here) - -
6 STEERING KNUCKLE SEAL 43215 - - -
7 TIE ROD END SUB-ASSEMBLY 45047 (Click here) - -
8 FRONT DISC BRAKE CALIPER ASSEMBLY - (Click here) - -
9 FRONT DISC 43512 (Click here) - -
10 FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY 48069 - - -
11 FRONT DRIVE SHAFT ASSEMBLY 43420 (Click here) - -
12 FRONT AXLE ASSEMBLY - (Click here) -

*A for HV Model TMC Made *B for TMMF Made
*1 FRONT FLEXIBLE HOSE - -
● Non-reusable part - -

C462334N02
4.156,1.417 4.417,0.896 4.417,0.896 4.583,0.896 false 1.26,1.729 1.594,1.729 false 5.583,2.844 5.844,2.323 5.844,2.323 6.01,2.323 false 6.281,2.177 6.667,2.531 0.385,0.354 18 false 13 4.656,0.74 5.083,1.094 0.427,0.354 18 false 14 1.104,1.646 1.385,2 0.281,0.354 10 false *1 1.188,0.271 1.542,0.531 0.354,0.26 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

13 FRONT AXLE HUB SUB-ASSEMBLY 43502C (Click here) - -
14 FRONT DISC BRAKE DUST COVER 47782 - - -

*1 STEERING KNUCKLE - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front axle hub sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
for HV Model TMC Made:
Auxiliary battery terminal is disconnected/reconnected
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Front wheel alignment adjustment for HV Model TMC Made:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for HV Model TMMF Made:
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
w/ Advanced Park:

Advanced Park


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system w/o Advanced Park:
(Click here)
w/ Advanced Park:
(Click here)
w/ Advanced Park:

Advanced Park


(Click here)

HINT:
for HV Model TMC Made

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model TMC Made)

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2. DISABLE BRAKE CONTROL (for HV Model TMC Made)

Z101186

Click here(Click here)

Hide 3.REMOVE FRONT WHEEL

Hide 43502H 4.REMOVE FRONT AXLE SHAFT NUT

a.
C446084N01
2.104,1.563 2.406,1.167 true 0.396,0.073 0.625,0.396 0.229,0.323 18 false i 3.667,0.031 3.854,0.354 0.188,0.323 18 true ii 1.927,1.604 2.292,1.771 0.365,0.167 10 true SST

i.

Using SST and a hammer, release the staked part of the front axle shaft nut.

SST
09930-00010  

NOTICE:

Loosen the staked part of the front axle shaft nut completely, otherwise the threads of the drive shaft may be damaged.



ii.

Using a 30 mm deep socket wrench, remove the front axle shaft nut while applying the brakes.



Hide 89543 5.SEPARATE FRONT SPEED SENSOR

a.
C462678N01
0.417,0.073 0.698,0.427 0.281,0.354 18 false i 3.99,0.073 4.271,0.427 0.281,0.354 18 false ii

i.

Remove the bolt and separate the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.



ii.

Remove the bolt, disengage the clamp and separate the front speed sensor from the front shock absorber assembly and steering knuckle.

NOTICE:
·

Prevent foreign matter from contacting the sensor tip.

·

Be careful not to damage the front speed sensor.

·

Clean the speed sensor installation hole and the contact surfaces every time the speed sensor is removed.





Hide 43215 6.REMOVE STEERING KNUCKLE SEAL (for TMMF Made)

Hide 45047 7.SEPARATE TIE ROD END SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 8.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Z101186

Click here(Click here)

Hide 43512 9.REMOVE FRONT DISC

Z101186

·

for TMC Made:

Click here(Click here)

·

for TMMF Made:

Click here(Click here)



Hide 48069 10.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

a.
C444459


Hide 43420 11.DISCONNECT FRONT DRIVE SHAFT ASSEMBLY

a.
C443133C03
2.906,0.26 3.323,0.26 3.323,0.26 3.323,0.979 true 2.99,0.469 3.323,0.469 true 3.24,0.979 3.448,1.156 0.208,0.177 10 true *a 0.417,0.063 0.635,0.344 0.219,0.281 18 false i 3.719,0.073 4.188,0.375 0.469,0.302 18 true ii, iii
*a Matchmark - -


i.

Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.


ii.

Using a plastic hammer, disconnect the front drive shaft assembly from the front axle assembly.

NOTICE:
·

Do not damage the front drive shaft outboard joint boot.

·

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.




iii.

If it is difficult to separate the front drive shaft assembly from the front axle assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.



Hide 12.REMOVE FRONT AXLE ASSEMBLY

a.
C443134N01
0.406,0.063 0.688,0.417 0.281,0.354 18 false i

i.

Remove the 2 bolts, 2 nuts and front axle assembly from the front shock absorber assembly.

NOTICE:

When removing the nuts, keep the bolts from rotating.




Hide 43502C 13.REMOVE FRONT AXLE HUB SUB-ASSEMBLY

a.
C443135N01
0.406,0.073 0.813,0.406 0.406,0.333 18 false i, ii

i.

Secure the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



ii.

Remove the 3 bolts, front axle hub sub-assembly and front disc brake dust cover from the steering knuckle.

NOTICE:
·

Do not drop the front axle hub sub-assembly.

·

Be careful not to damage the speed sensor rotor or contact surfaces.

·

Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.





Hide 47782 14.REMOVE FRONT DISC BRAKE DUST COVER

a.
C443136