Refer to DTC C05121F.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C051212 | Right Rear Wheel Speed Sensor Circuit Short to Battery | The speed sensor short signal is ON continuously for 0.5 seconds or more. | ·
Rear speed sensor RH (rear axle hub and bearing assembly RH) ·
Skid control sensor wire RH (No. 1 parking brake wire assembly) ·
Wire harness and connector ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | A |
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the u2 rear speed sensor RH (rear axle hub and bearing assembly RH) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Pre-procedure2
Turn the ignition switch to ON.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(u2)Location & Routingewd_type=routing;type=c;code=u2 |
||
| u2-2 (+) - u2-1 (-) | Ignition switch ON | 11 to 14 V |
The rear speed sensor RH is incorporated into the rear axle hub and bearing assembly RH.
If the rear speed sensor RH needs to be replaced, replace the rear axle hub and bearing assembly RH.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Disconnect the uO1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Pre-procedure3
Turn the ignition switch to ON.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(uO1)Location & Routingewd_type=routing;type=w;code=uO1 Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO1;pinno=4,3 |
||
| uO1-4 (RR+) - uO1-3 (RR-) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure2
Disconnect the A94 skid control ECU (brake actuator assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(uO1)Location & Routingewd_type=routing;type=w;code=uO1 Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO1;pinno=3 |
||
| uO1-3 (RR-) - Body ground | Always | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(uO1,A94)Location & Routingewd_type=routing;type=w,c;code=uO1,A94 Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO1;pinno=4,3 Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A94;pinno=20,19 |
||
| uO1-4 (RR+) or A94-20 (RR+) - uO1-3 (RR-) or A94-19 (RR-) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG