Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484413 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C051D54  Multi-axis Acceleration Sensor Module "A" Missing Calibration  C121054  Yaw Rate Sensor Missing Calibration  


DESCRIPTION

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.

HINT:

If there is a malfunction in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTCs U012587 are output. When DTCs U012587 are output together with C051D54 and/or C121054, inspect and repair the trouble areas indicated by U012587 first.


These DTCs are also output when the calibration has not been completed.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C051D54 Multi-axis Acceleration Sensor Module "A" Missing Calibration Zero point calibration of acceleration sensor undone.
·

Acceleration sensor zero point not calibrated

·

Acceleration sensor (airbag sensor assembly) installation

·

Acceleration sensor (airbag sensor assembly)

·

Skid control ECU (brake actuator assembly)


Brake/EPB A
C121054 Yaw Rate Sensor Missing Calibration Zero point calibration of yaw rate sensor undone. Yaw rate sensor zero point not calibrated Brake/EPB A

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

HINT:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

B

2.PERFORM CALIBRATION
2.PERFORM CALIBRATION
a.

Operate the GTS to perform "Calibration".

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION


Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 4554

Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Operate the GTS to clear the codes.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Operate the GTS to read the DTCs.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
C051D54 and C121054 are not output A
C051D54 or C121054 is output B



A

END

B

5.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
5.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION


OK:

The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.READ VALUE USING GTS (YAW RATE SENSOR VALUE)

NG

6.READ VALUE USING GTS (YAW RATE SENSOR VALUE)
a.

Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Yaw Rate Sensor Value Yaw rate sensor Min.: -128°/s
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Chassis > Brake/EPB > Data List
Tester Display
Yaw Rate Sensor Value
50003 435 29
OK:

The yaw rate sensor value is normal.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (LATERAL G)

NG

7.READ VALUE USING GTS (LATERAL G)
a.

Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lateral G Lateral G Min.: -25.105 m/s2
Max.: 24.908 m/s2
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning:
Changes in proportion with lateral acceleration
Chassis > Brake/EPB > Data List
Tester Display
Lateral G
50003 435 25
OK:

The lateral G value is normal.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (FORWARD AND REARWARD G)

NG

8.READ VALUE USING GTS (FORWARD AND REARWARD G)
a.

Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Forward and Rearward G Forward and Rearward G Min.: -25.105 m/s2
Max.: 24.908 m/s2
During deceleration:-25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration/deceleration:
Changes in proportion with acceleration
Chassis > Brake/EPB > Data List
Tester Display
Forward and Rearward G
50003 435 26
OK:

The forward and rearward G value is normal.



Result:
Proceed to
OK
NG



OK

NG