Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for HV Model TMC Made) › from 2021.07
RM3700E _54 Brake _093729 PARKING BRAKE _0484414 ELECTRIC PARKING BRAKE SYSTEM(for HV Model TMC Made) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for HV Model TMC Made)  C060962  Electric Parking Brake Switch Signal Compare Failure  


DESCRIPTION

When the electric parking brake switch assembly is pulled, a lock request signal is sent from the parking brake ECU (brake actuator assembly) to the parking brake actuator assembly. When the electric parking brake switch assembly is pulled, a release request signal is sent from the parking brake ECU (brake actuator assembly) to the parking brake actuator assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
C060962 Electric Parking Brake Switch Signal Compare Failure
·

Parking brake switch open or short circuit is detected for 1 second or more

·

Parking brake switch stuck malfunction


·

Electric parking brake switch assembly

·

Wire harness or connector

·

Parking brake ECU (brake actuator assembly)


DTC stored Electric Parking Brake A An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition - - - -
Malfunction Status Parking brake switch open circuit is detected ○ - -
Parking brake switch short circuit is detected - ○ -
Parking brake switch stuck malfunction - - ○
Detection Time 1 second or more 1 second or more -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C367775E81
1.333,3.167 3.885,3.531 2.552,0.365 10 false Electric Parking Brake Switch Assembly 5.167,3.667 6.833,4.323 1.667,0.656 10 false Parking Brake ECU (Brake Actuator Assembly) 5.167,3.5 5.604,3.688 0.438,0.188 10 false A95 1.333,3 1.833,3.25 0.5,0.25 10 false H140 3.333,1.25 3.771,1.438 0.438,0.188 10 false SWI1 3.26,1.563 3.792,1.75 0.531,0.188 10 false SWO1 3.323,1.865 3.76,2.052 0.438,0.188 10 false SWI2 3.25,2.427 3.781,2.615 0.531,0.188 10 false SWO2 5.469,1.365 5.906,1.552 0.438,0.188 10 false SWI1 5.458,1.646 5.938,1.833 0.479,0.188 10 false SWO1 5.458,1.969 5.896,2.156 0.438,0.188 10 false SWI2 5.469,2.563 5.979,2.75 0.51,0.188 10 false SWO2 3.792,1.25 3.979,1.448 0.188,0.198 10 false 7 3.792,1.552 4.052,1.75 0.26,0.198 10 false 8 5.198,1.563 5.385,1.76 0.188,0.198 10 false 20 3.802,1.844 3.99,2.042 0.188,0.198 10 false 1 3.813,2.438 4,2.635 0.188,0.198 10 false 2 5.188,1.26 5.375,1.458 0.188,0.198 10 false 14 5.198,1.865 5.385,2.063 0.188,0.198 10 false 24 5.188,2.448 5.375,2.646 0.188,0.198 10 false 22

CAUTION / NOTICE / HINT

NOTICE:
·

When the electric parking brake switch assembly is pulled and held for 1 second or more without being pulled fully to the lock side, both of the 2 linked contacts may turn OFF causing this DTC to be stored (this is not a system malfunction).

·

To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the parking brake ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY

·

When replacing the parking brake ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned ON.



PROCEDURE

1.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

OK

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the H140 electric parking brake switch assembly connector.


b.

Disconnect the A95 parking brake ECU (brake actuator assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A95,H140)Location & Routing

Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

Click Connector(H140)Instrument Panel>Instrument Panel Wire / Speaker Wire>Electric Parking Brake Switch Assembly

A95-14 (SWI1) - H140-7 (SWI1) Always Below 1 Ω
A95-20 (SWO1) - H140-8 (SWO1) Always Below 1 Ω
A95-24 (SWI2) - H140-1 (SWI2) Always Below 1 Ω
A95-22 (SWO2) - H140-2 (SWO2) Always Below 1 Ω
A95-14 (SWI1) or H140-7 (SWI1) - Body ground Always 10 kΩ or higher
A95-20 (SWO1) or H140-8 (SWO1) - Body ground Always 10 kΩ or higher
A95-24 (SWI2) or H140-2 (SWI2) - Body ground Always 10 kΩ or higher
A95-22 (SWO2) or H140-2 (SWO2) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Electric Parking Brake > Clear DTCs
50002 485
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Check for DTCs.

Chassis > Electric Parking Brake > Trouble Codes
50001 485

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY)

B