Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › PRE-COLLISION SYSTEM › from 2021.07
RM3700E _95 ADAS / AD _095278 ADVANCED DRIVER ASSISTANCE SYSTEM _0447900 PRE-COLLISION SYSTEM C

ADVANCED DRIVER ASSISTANCE SYSTEM  PRE-COLLISION SYSTEM  U023A87  Lost Communication with Image Processing Module "A" Missing Message  


DESCRIPTION

w/ Adaptive High Beam System:

The millimeter wave radar sensor assembly is connected to the forward recognition camera and headlight ECU sub-assembly LH via the CAN communication line. If the millimeter wave radar sensor assembly receives signals indicating that its communication with the forward recognition camera is abnormal, the millimeter wave radar sensor assembly stores DTC U023A87.


w/o Adaptive High Beam System:

The millimeter wave radar sensor assembly is connected to the forward recognition camera via the CAN communication line. If the millimeter wave radar sensor assembly receives signals indicating that its communication with the forward recognition camera is abnormal, the millimeter wave radar sensor assembly stores DTC U023A87.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
U023A87 Lost Communication with Image Processing Module "A" Missing Message When the ignition switch is ON for 3 seconds or more, a forward recognition camera communication malfunction continues for approximately 3 seconds or more.
·

Forward recognition camera

·

Millimeter wave radar sensor assembly

·

Headlight ECU sub-assembly LH*


Pre-Collision System B

*: w/ Adaptive High Beam System


w/ Adaptive High Beam System
Pattern DTC output part name
(Display on GTS)
Suspected Area (Malfunction Status)
Millimeter Wave Radar Sensor Assembly Forward Recognition Camera Headlight ECU Sub-assembly LH
Pre-Collision System Radar Cruise2 Lane Control Forward Recognition Camera (Front Lighting Control) Headlight Control
U023A87 U023A87 U023587 U023587 U023A87

○: DTC is output

-: DTC is not output

Pattern 1 ○ ○ ○ ○ ○ Harness or connector (Open or short)
Headlight ECU sub-assembly LH (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)
Pattern 2 ○ ○ ○ ○ - Harness or connector (Open or short)
Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)
Pattern 3 ○ ○ - - - Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)

w/o Adaptive High Beam System
Pattern DTC output part name
(Display on GTS)
Suspected Area (Malfunction Status)
Millimeter Wave Radar Sensor Assembly Forward Recognition Camera
Pre-Collision System Radar Cruise2 Lane Control Forward Recognition Camera (Front Lighting Control)
U023A87 U023A87 U023587 U023587

○: DTC is output

-: DTC is not output

Pattern 1 ○ ○ ○ ○ Harness or connector (Open or short)
Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)
Pattern 2 ○ ○ - - Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)

HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.


WIRING DIAGRAM

w/ Adaptive High Beam System


C424986E05
0.302,1.24 0.76,1.438 0.458,0.198 10 false A110 0.302,1.406 2.896,1.885 2.594,0.479 10 false Headlight ECU Sub-assembly LH 1.104,0.448 1.563,0.646 0.458,0.198 10 false LCH 1.125,0.938 1.583,1.135 0.458,0.198 10 false LCL 1.51,0.333 1.823,0.531 0.313,0.198 10 false 22 1.51,0.802 1.823,1 0.313,0.198 10 false 21 5.229,0.813 5.542,1.01 0.313,0.198 10 false 12 5.292,0.333 5.448,0.531 0.156,0.198 10 false 6 5.292,2.76 5.448,2.958 0.156,0.198 10 false 6 5.292,2.292 5.448,2.49 0.156,0.198 10 false 5 5.521,0.333 6.135,0.531 0.615,0.198 10 false CANH 5.521,1.031 6.135,1.229 0.615,0.198 10 false CANL 5.521,2.281 6.135,2.479 0.615,0.198 10 false CA1P 5.521,2.99 6.135,3.188 0.615,0.198 10 false CA1N 4.99,1.188 5.448,1.385 0.458,0.198 10 false V10 4.427,3.135 4.885,3.333 0.458,0.198 10 false B8 4.99,1.365 7.021,1.771 2.031,0.406 10 false Forward Recognition Camera 4.417,3.313 7.125,3.688 2.708,0.375 10 false Millimeter Wave Radar Sensor Assembly


w/o Adaptive High Beam System


C424985E06
5.333,1.073 5.646,1.271 0.313,0.198 10 false B8 5.333,1.229 6.74,1.625 1.406,0.396 10 false Millimeter Wave Radar Sensor Assembly 0.542,1.094 0.885,1.302 0.344,0.208 10 false V10 5.49,0.854 5.917,1.052 0.427,0.198 10 false CA1N 0.542,1.26 1.813,1.677 1.271,0.417 10 false Forward Recognition Camera 5.281,0.188 5.625,0.396 0.344,0.208 10 false 5 5.271,0.635 5.594,0.833 0.323,0.198 10 false 6 5.49,0.167 5.927,0.365 0.438,0.198 10 false CA1P 1,0.188 1.448,0.333 0.448,0.146 10 false CANH 1,0.833 1.448,0.979 0.448,0.146 10 false CANL 1.49,0.667 1.833,0.875 0.344,0.208 10 false 12 1.5,0.177 1.844,0.385 0.344,0.208 10 false 6


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.

HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT


·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera adjustment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT


·

w/ Adaptive High Beam System:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>INITIALIZATION

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal. Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery. Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

If there are communication malfunctions for systems other than the millimeter wave radar sensor assembly and forward recognition camera, refer to "HOW TO PROCEED WITH TROUBLESHOOTING" for the CAN Communication System.

for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Adaptive High Beam System A
w/o Adaptive High Beam System B



A

2.CHECK FOR DTCs

B

11.CHECK FOR DTC
2.CHECK FOR DTCs
a.

Read each DTC and check the diagnosis pattern using the table below.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Powertrain > Radar Cruise2 > Trouble Codes
50001 426
Chassis > Lane Control > Trouble Codes
50001 418
Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433
Body Electrical > Headlight Control > Trouble Codes
50001 462
Pattern DTC output part name
(Display on GTS)
Pre-Collision System Radar Cruise2 Lane Control Forward Recognition Camera (Front Lighting Control) Headlight Control
Pattern 1 U023A87 U023A87 U023587 U023587 U023A87
Pattern 2 U023A87 U023A87 U023587 U023587 -
Pattern 3 U023A87 U023A87 - - -


Result:
Result Proceed to
Pattern 1 A
Pattern 2 B
Pattern 3 C



A

3.CLEAR DTC

B

8.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

C

10.CHECK FORWARD RECOGNITION CAMERA
3.CLEAR DTC

Pre-procedure1

a.

Disconnect the A110 headlight ECU sub-assembly LH connector.


Procedure1

a.

Clear the DTCs.

Body Electrical > Pre-Collision System > Clear DTCs
50002 432
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH
4.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH
a.

Check for DTCs.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Result:
Result Proceed to
U023A87 is not output A
U023A87 is output B




A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

5.CLEAR DTC
5.CLEAR DTC

Pre-procedure1

a.

Connect the A110 headlight ECU sub-assembly LH connector.


b.

Disconnect the V10 forward recognition camera connector.


Procedure1

a.

Clear the DTCs.

Body Electrical > Pre-Collision System > Clear DTCs
50002 432
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

6.INSPECT FORWARD RECOGNITION CAMERA
6.INSPECT FORWARD RECOGNITION CAMERA
a.

Check for DTCs.

Body Electrical > Headlight Control > Trouble Codes
50001 462
Result:
Result Proceed to
U023A87 is not output A
U023A87 is output B




A

REPLACE FORWARD RECOGNITION CAMERA

B

7.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
7.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

Pre-procedure1

a.

Connect the V10 forward recognition camera connector.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B8)Location & Routing

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

B8-5 (CA1P) - B8-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
B8-5 (CA1P) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B8-6 (CA1N) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B8-5 (CA1P) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
B8-6 (CA1N) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B8)Location & Routing

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

B8-5 (CA1P) - B8-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
B8-5 (CA1P) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B8-6 (CA1N) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B8-5 (CA1P) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
B8-6 (CA1N) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

9.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)
9.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the V10 forward recognition camera connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V10)Location & Routing

Click Connector(V10)Body>No. 1 Roof Wire>Forward Recognition Camera

V10-6 (CANH) - V10-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
V10-6 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V10-12 (CANL) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V10-6 (CANH) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
V10-12 (CANL) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE CAN BUS SUB LINE OR CONNECTOR

10.CHECK FORWARD RECOGNITION CAMERA

Pre-procedure1

a.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

a.

Measure the waveform according the table below.

Measurement Condition:
Tester Connection Condition Condition Specified Condition

Click Location & Routing(B8)Location & Routing

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

B8-5 (CA1P) - B8-6 (CA1N) Ignition switch ON 1V/DIV., 100μs./DIV. Waveform generation


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPLACE FORWARD RECOGNITION CAMERA

11.CHECK FOR DTC
a.

Read each DTC and check the diagnosis pattern using the table below.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432
Powertrain > Radar Cruise2 > Trouble Codes
50001 426
Chassis > Lane Control > Trouble Codes
50001 418
Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433

Pattern DTC output part name
(Display on GTS / Output DTC)
Radar Cruise2 Pre-Collision System Lane Control Forward Recognition Camera (Front Lighting Control)
Pattern 1 U023A87 U023A87 U023587 U023587
Pattern 2 U023A87 U023A87 - -

Result:
Result Proceed to
Pattern 1 A
Pattern 2 B



A

12.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

B

14.CHECK FORWARD RECOGNITION CAMERA
12.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B8)Location & Routing

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

B8-5 (CA1P) - B8-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
B8-5 (CA1P) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B8-6 (CA1N) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B8-5 (CA1P) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
B8-6 (CA1N) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

13.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)
13.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the V10 forward recognition camera connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V10)Location & Routing

Click Connector(V10)Body>No. 1 Roof Wire>Forward Recognition Camera

V10-6 (CANH) - V10-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
V10-6 (CANH) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V10-12 (CANL) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V10-6 (CANH) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
V10-12 (CANL) - +B Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE CAN BUS SUB LINE OR CONNECTOR

14.CHECK FORWARD RECOGNITION CAMERA

Pre-procedure1

a.

Disconnect the B8 millimeter wave radar sensor assembly connector.


Procedure1

a.

Measure the waveform according the table below.

Measurement Condition:
Tester Connection Condition Condition Specified Condition

Click Location & Routing(B8)Location & Routing

Click Connector(B8)Engine Compartment>No. 3 Engine Room Wire>Millimeter Wave Radar Sensor Assembly

B8-5 (CA1P) - B8-6 (CA1N) Ignition switch ON 1V/DIV., 100μs./DIV. Waveform generation


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPLACE FORWARD RECOGNITION CAMERA