On the SIGNAL CHECK screen, it is possible to check if the signals sent to the parking assist ECU are normal.
On the SIGNAL CHECK screen, "OK" (blue) is displayed for items with a normal inspection result or input state.
On the SIGNAL CHECK screen, "CHK" (red) is displayed for items with an abnormal inspection result or input state.
Displayed items may differ depending on vehicle specifications.
| Item | Signal Input Method | Detail | DTC Output when Abnormal Result is Displayed | Signal Receiver |
|---|---|---|---|---|
| CAN | CAN communication | CAN communication signal | DTC is output | Related ECUs |
| CAMERA SW | Vehicle wire harness | Panoramic view monitor switch signal input state | DTC is not output | Panoramic view monitor switch |
| SHIFT | Vehicle wire harness | Power distribution box assembly signal input state | DTC is not output | Power distribution box assembly |
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Check which items display on the signal check screen.
| Result | Proceed to |
|---|---|
| "CAMERA SW" displays "CHK" (red) | A |
| "SHIFT" displays "CHK" (red) | B |
| "CAN" displays "CHK" (red) | C |
A
B
C
Disconnect the H22 panoramic view monitor switch connector.
Disconnect the O118 parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O118,H22)Location & Routingewd_type=routing;type=c,c;code=O118,H22 Click Connector(O118)Body>Floor Wire>Parking Assist ECUewd_type=component;type=c;code=O118;pinno=15 Click Connector(H22)Instrument Panel>Instrument Panel Wire / Speaker Wire>Panoramic View Monitor Switchewd_type=component;type=c;code=H22;pinno=5,2 |
||
| O118-15 (BLSW) - H22-5 (D) | Always | Below 1 Ω |
| H22-2 (E) - Body ground | Always | Below 1 Ω |
| O118-15 (BLSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SWITCH>REMOVAL
Check that the back-up light comes on.
The back-up light comes on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/ Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>HOW TO PROCEED WITH TROUBLESHOOTING
w/o Adaptive High Beam System: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Adaptive High Beam System)>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the O118 parking assist ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O118)Location & Routingewd_type=routing;type=c;code=O118 Click Connector(O118)Body>Floor Wire>Parking Assist ECUewd_type=component;type=c;code=O118;pinno=14 |
||
| O118-14 (REV) - Body ground | Ignition switch ON, shift lever in R | 11 to 14 V |
| O118-14 (REV) - Body ground | Ignition switch ON, shift lever not in R | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG