Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for M15A-FXE TMMF Made) › from 2021.07
RM3700E _52 Drivetrain _094372 DRIVE SHAFT / PROPELLER SHAFT _0481085 FRONT DRIVE SHAFT ASSEMBLY(for M15A-FXE TMMF Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for M15A-FXE TMMF Made)  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
C462331N01
4.833,2.51 7.083,3.844 2.25,1.333 1.656,0.906 1.854,0.635 1.854,0.635 2.021,0.635 false 1.979,1.229 2.177,0.958 2.177,0.958 2.344,0.958 false 2.406,1.354 2.604,1.083 2.604,1.083 2.771,1.083 false 2.813,1.552 3.01,1.281 3.01,1.281 3.177,1.281 false 3.406,1.885 3.604,1.615 3.604,1.615 3.771,1.615 false 3.969,2.188 4.167,1.917 4.167,1.917 4.333,1.917 false 4.51,2.667 4.76,2.313 4.76,2.313 4.927,2.313 false 5.052,2.979 5.25,2.708 5.25,2.708 5.417,2.708 false 5.594,3.219 5.792,2.948 5.792,2.948 5.958,2.948 false 6.094,3.583 6.292,3.313 6.292,3.313 6.458,3.313 false 6.438,0.208 6.771,0.208 false 3.281,4.125 3.094,4.365 3.094,4.365 2.927,4.365 false 2.51,3.76 2.323,4 2.323,4 2.156,4 false 1.698,3.104 1.51,3.344 1.51,3.344 1.344,3.344 false 4.708,4.781 4.521,5.021 4.521,5.021 4.354,5.021 false 4.885,2.563 5.26,2.802 0.375,0.24 12 false *A 2.333,0.5 2.885,0.854 0.552,0.354 18 false 6 5.354,2.177 5.906,2.531 0.552,0.354 18 false 9 4.76,1.771 5.313,2.125 0.552,0.354 18 false 7 3.594,1.146 4.146,1.5 0.552,0.354 18 false 8 2.385,0.865 2.573,1.083 0.188,0.219 10 false ● 2.813,0.979 3.208,1.219 0.396,0.24 10 false *1 1.167,3.229 1.479,3.542 0.313,0.313 18 false 3 2,3.885 2.292,4.208 0.292,0.323 18 false 1 2.74,4.24 3.052,4.594 0.313,0.354 18 false 2 6.26,2.833 6.625,3.156 0.365,0.323 18 false 4 3.813,1.531 4.292,1.74 0.479,0.208 10 false ● *2 5.833,2.573 6.188,2.906 0.354,0.333 18 false 5 6.125,0.083 6.677,0.438 0.552,0.354 18 false 10 3.469,1.188 3.656,1.406 0.188,0.219 10 false ● 4.635,1.823 4.823,2.042 0.188,0.219 10 false ● 5.229,2.219 5.417,2.438 0.188,0.219 10 false ● 5.708,2.615 5.896,2.833 0.188,0.219 10 false ● 6.74,3.198 6.927,3.417 0.188,0.219 10 false ● 1.042,3.271 1.229,3.49 0.188,0.219 10 false ● 1.875,3.906 2.063,4.125 0.188,0.219 10 false ● 2.604,4.271 2.792,4.49 0.188,0.219 10 false ● 6.865,3.167 7.094,3.479 0.229,0.313 18 false 5 4.188,4.938 4.583,5.177 0.396,0.24 10 false *3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT AXLE OUTBOARD JOINT BOOT - (Click here) - -
2 FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP 43447F (Click here) - -
3 FRONT AXLE OUTBOARD JOINT BOOT CLAMP 43447E (Click here) - -
4 FRONT DRIVE SHAFT DAMPER RH 43474D (Click here) - -
5 FRONT DRIVE SHAFT DAMPER CLAMP RH 43474F (Click here) - -
6 FRONT DRIVE INBOARD JOINT ASSEMBLY 43040 (Click here) - -
7 FRONT AXLE INBOARD JOINT BOOT - (Click here) - -
8 FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP 43448G (Click here) - -
9 FRONT AXLE INBOARD JOINT BOOT CLAMP 43448F (Click here) - -
10 INSPECT FRONT DRIVE SHAFT ASSEMBLY - (Click here) - -

*A for RH Side - -
*1 TRIPOD JOINT *2 FRONT AXLE INBOARD JOINT GROMMET
*3 FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

a.
C445316C03
0.719,0.333 1.219,0.635 0.5,0.302 18 false i 4.094,0.302 4.646,0.656 0.552,0.354 18 false ii 0.708,2.167 1.26,2.521 0.552,0.354 18 false iii 4.063,2.146 4.344,2.5 0.281,0.354 18 false iv
V100135

Outboard Joint Side
V100136

Inboard Joint Side
V100137

Parts insertion direction
V100138

Grease


i.

Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


ii.

Install new parts to the front drive outboard joint shaft assembly in the following order:

1. Front No. 2 axle outboard joint boot clamp

2. Front axle outboard joint boot

3. Front axle outboard joint boot clamp


iii.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard Grease Capacity:

87 to 97 g (3.07 to 3.42 oz)



iv.

Install the front axle outboard joint boot to the front drive outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.





Hide 43447F 2.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.
C464075N01
1.219,0.625 2.021,0.781 true 6.01,0.896 6.583,1.469 true 0.385,0.042 1.5,0.417 1.115,0.375 18 false i, ii, iii, iv 3.958,0.052 4.51,0.406 0.552,0.354 18 false v, vi 0.917,0.521 1.375,0.719 0.458,0.198 10 false SST 6.5,1.5 6.958,1.698 0.458,0.198 10 false SST

i.

Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot.


ii.

Place SST onto the front No. 2 axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


iii.

Tighten SST so that the front No. 2 axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



iv.

Remove SST.


v.

Using SST, measure the clearance of the front No. 2 axle outboard joint boot clamp.

SST
09240-00021  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)



vi.

If the clearance is not as specified, retighten SST.



Hide 43447E 3.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

a.
C464076N01
0.979,0.75 1.781,0.906 true 5.708,1.042 6.281,1.219 true 0.385,0.042 1.5,0.417 1.115,0.375 18 false i, ii, iii, iv 3.958,0.052 4.51,0.406 0.552,0.354 18 false v, vi 0.688,0.656 1.146,0.854 0.458,0.198 10 false SST 6.344,1.135 6.802,1.333 0.458,0.198 10 false SST

i.

Install the front axle outboard joint boot clamp to the front axle outboard joint boot.


ii.

Place SST onto the front axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


iii.

Tighten SST so that the front axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



iv.

Remove SST.


v.

Using SST, measure the clearance of the front axle outboard joint boot clamp.

SST
09240-00021  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)



vi.

If the clearance is not as specified, retighten SST.



Hide 43474D 4.INSTALL FRONT DRIVE SHAFT DAMPER RH (for RH Side)

a.
C445413N01
0.458,0.073 1,0.417 0.542,0.344 18 false i, ii 3.479,0.208 3.792,0.406 0.313,0.198 10 false A

i.

Temporarily install the front drive shaft damper RH and 2 new front drive shaft damper clamps RH to the front drive outboard joint shaft assembly as shown in the illustration.


ii.

Set the dimension (A) as specified below.

Dimension (A):

481 to 485 mm (1.58 to 1.59 ft.)




Hide 43474F 5.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP RH (for RH Side)

Z101186

HINT:

Use the same procedure for each front drive shaft damper clamp RH.



a.
C464077N01
1.49,0.458 1.896,0.927 true 4.469,1.042 4.938,1.042 true 0.385,0.042 1.167,0.396 0.781,0.354 18 false i, ii, iii 3.958,0.052 4.51,0.406 0.552,0.354 18 false iv, v 1.188,0.354 1.646,0.552 0.458,0.198 10 false SST 4.167,0.958 4.625,1.156 0.458,0.198 10 false SST

i.

Place SST onto the front drive shaft damper clamp RH, press it against the damper and slightly tighten SST.

SST
09521-24010  


ii.

Tighten SST so that the front drive shaft damper clamp RH is pinched.

NOTICE:

Do not overtighten SST.



iii.

Remove SST.


iv.

Using SST, measure the clearance of the front drive shaft damper clamp RH.

SST
09240-00021  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)



v.

If the clearance is not as specified, retighten SST.



Hide 43040 6.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
C464078C01
5.719,4.74 5.031,4.5 5.031,4.5 5.865,4.333 true 2.292,3.167 2.635,3.635 2.635,3.635 1.802,3.417 true 2.823,1.615 2.563,1.344 true 0.396,0.177 0.677,0.531 0.281,0.354 18 false i 3.958,0.177 4.51,0.531 0.552,0.354 18 false ii, iii 0.385,2.063 0.969,2.375 0.583,0.313 18 false iv, v 3.938,2.063 4.292,2.417 0.354,0.354 18 false vi 0.333,4 0.677,4.333 0.344,0.333 18 false vii 3.917,4 4.469,4.354 0.552,0.354 18 false viii 4.844,4.417 5.146,4.677 0.302,0.26 10 false *b 2.688,3.563 3,3.76 0.313,0.198 10 false *b 2.875,1.552 3.177,1.813 0.302,0.26 10 false *a
*a Groove *b Matchmark
V100135

Outboard Joint Side
V100136

Inboard Joint Side
V100137

Parts insertion direction
V100138

Grease


i.

Install a new front axle inboard joint grommet to the inboard joint groove.

NOTICE:

Securely fit the protrusion on the front axle inboard joint grommet into the inboard joint groove.



ii.

Install new parts to the front drive outboard joint shaft assembly in the following order:

1. Front axle inboard joint boot clamp

2. Front axle inboard joint boot

3. Front No. 2 axle inboard joint boot clamp


iii.

Remove the protective tape.


iv.

Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



v.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.

·

Be sure to install the tripod joint in the correct direction.




vi.

Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.


vii.

Pack the front drive inboard joint assembly and front axle inboard joint boot with grease.

Standard Grease Capacity:
for LH Side 126 to 136 g (4.44 to 4.80 oz)
for RH Side 155 to 165 g (5.47 to 5.82 oz)



viii.

Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.



Hide 7.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.
C464079N01
0.396,0.052 0.677,0.406 0.281,0.354 18 false i

i.

Install the front axle inboard joint boot to the front drive inboard joint assembly.

NOTICE:
·

Keep the grooves free of grease.

·

Keep the inside of the front axle inboard joint boot free of foreign matter.





b.
C464080N01
0.396,0.052 0.677,0.406 0.281,0.354 18 false i 3.333,1.208 3.49,1.406 0.156,0.198 10 false A

i.

Check whether the dimension (A) of each drive shaft is within the specification.

Dimension (A):
for LH Side 627.95 mm (2.06 ft.)
for RH Side 840.9 mm (2.76 ft.)


NOTICE:

Keep the drive shaft assembly level during inspection.




Hide 43448G 8.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.
C464081N01
1.219,0.625 2.021,0.781 true 6.01,0.896 6.583,1.469 true 0.385,0.042 1.5,0.417 1.115,0.375 18 false i, ii, iii, iv 3.958,0.052 4.51,0.406 0.552,0.354 18 false v, vi 0.917,0.521 1.375,0.719 0.458,0.198 10 false SST 6.5,1.5 6.958,1.698 0.458,0.198 10 false SST

i.

Install the front No. 2 axle inboard joint boot clamp to the front axle inboard joint boot.


ii.

Place SST onto the front No. 2 axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


iii.

Tighten SST so that the front No. 2 axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



iv.

Remove SST.


v.

Using SST, measure the clearance of the front No. 2 axle inboard joint boot clamp.

SST
09240-00021  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)



vi.

If the clearance is not as specified, retighten SST.



Hide 43448F 9.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

a.
C464082N01
0.979,0.75 1.781,0.906 true 5.594,1.042 6.167,1.219 true 0.385,0.042 1.5,0.417 1.115,0.375 18 false i, ii, iii, iv 3.958,0.052 4.51,0.406 0.552,0.354 18 false v, vi 0.688,0.656 1.146,0.854 0.458,0.198 10 false SST 6.229,1.135 6.688,1.333 0.458,0.198 10 false SST

i.

Install the front axle inboard joint boot clamp to the front axle inboard joint boot.


ii.

Place SST onto the front axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


iii.

Tighten SST so that the front axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



iv.

Remove SST.


v.

Using SST, measure the clearance of the front axle inboard joint boot clamp.

SST
09240-00021  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)



vi.

If the clearance is not as specified, retighten SST.