The certification ECU (smart key ECU assembly) has a power source mode switching function.
This DTC is stored when the IGE input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock ECU (steering lock actuator or upper bracket assembly) is determined to be abnormal.
The steering lock ECU (steering lock actuator or upper bracket assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator or upper bracket assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| B278211 | Power Source Control System Circuit Short to Ground | Either of the following conditions is met (1-trip detection logic (Only output while a malfunction is present and the ignition switch is ON.)):
·
The steering lock motor activation command circuit has a short circuit. ·
The steering lock motor activation command circuit has an open circuit.
|
·
Steering lock ECU (steering lock actuator or upper bracket assembly) ·
Certification ECU (smart key ECU assembly) ·
Wire harness or connector |
Entry&Start | B | DTC Output Confirmation Operation:
Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift lever in P (for CVT) and the ignition switch off. The steering unlocks when the ignition switch is turned to ACC or ON while carrying the key.) |
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
| The steering cannot be locked or unlocked. For this reason, the engine cannot be started. | Prohibits the engine from being started (the engine does not start). |
| DTC No. | Data List and Active Test |
|---|---|
| B278211 | - |
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.
Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly), refer to Service Bulletin.
Pre-procedure1
Perform the DTC output confirmation operation.
Procedure1
Check if DTC B278588 is output.
| Result | Proceed to |
|---|---|
| B278588 is not output | A |
| B278588 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H71)Location & Routingewd_type=routing;type=c;code=H71 Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assemblyewd_type=component;type=c;code=H71;pinno=1 |
||
| H71-1 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Connect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Procedure1
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
| *b | Steering lock motor not operating |
| *c | Steering lock motor operating |
Check the signal waveform according to the condition(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | H71-3 (IGE) - H71-1 (GND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Condition | Steering lock motor operating when all conditions met, and then door opened:
·
Shift lever in P*1 ·
Steering unlocked ·
Ignition switch turned off |
*1: for CVT
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the cable from the negative (-) auxiliary battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) auxiliary battery terminal to clear the record of malfunctions stored in the Data List.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Perform the DTC output confirmation operation.
Procedure1
Check if DTC B278215 is output.
| Result | Proceed to |
|---|---|
| B278215 is not output | A |
| B278215 is output | B |
Post-procedure1
None
A
B
Pre-procedure1
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Disconnect the H46 certification ECU (smart key ECU assembly) connector.
Procedure1
Check for deformation and corrosion of the connector case and terminals.
There is no deformation or corrosion of the connector case or terminals.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H71,H46)Location & Routingewd_type=routing;type=c,c;code=H71,H46 Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assemblyewd_type=component;type=c;code=H71;pinno=3,1 Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H46;pinno=24 |
||
| H71-3 (IGE) - H46-24 (SLR+) | Always | Below 1 Ω |
| H71-1 (GND) - Body ground | Always | Below 1 Ω |
| H71-3 (IGE) or H46-24 (SLR+) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG