Home › General › MAINTENANCE › REAR BRAKE FLEXIBLE HOSE (for AWD) › from 2021.07
RM3700E _V1 General _093024 MAINTENANCE _0447176 REAR BRAKE FLEXIBLE HOSE(for AWD) A

MAINTENANCE  REAR BRAKE FLEXIBLE HOSE(for AWD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C449849N02
6.333,0.698 6.667,0.698 false 6.333,0.292 6.667,0.292 false 3.938,3.958 4.271,3.958 false 4.083,2.698 3.917,2.698 3.917,2.698 3.458,2.188 true 4.521,1.115 4.854,1.115 false 4.313,0.615 4.646,0.615 false 4.833,1.906 5.167,1.906 false 5.229,0.156 5.51,0.51 0.281,0.354 18 false 1 5.375,0.219 5.729,0.573 0.354,0.354 12 false (*A) 5.688,0.156 6.042,0.479 0.354,0.323 18 false , 2 3.75,3.823 4.031,4.177 0.281,0.354 18 false 3 6.156,0.563 6.438,0.917 0.281,0.354 18 false 4 4.427,2.615 4.635,2.969 0.208,0.354 18 false 5 4.938,1.031 5.292,1.385 0.354,0.354 10 false ● 6,0.219 6.354,0.573 0.354,0.354 12 false (*A) 4.708,0.521 5.063,0.875 0.354,0.354 10 false ● 5.229,1.792 5.583,2.146 0.354,0.354 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - - - (Click here)
3 REAR WHEEL - - - -
4 DRAIN BRAKE FLUID - - (Click here) -
5 REAR FLEXIBLE HOSE 47319F (Click here) - -

*A for HV Model - -
*1 BRAKE LINE - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear brake flexible hose removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

NOTICE:

If both left and right rear flexible hoses are disconnected at the same time, be sure to place an identification mark on each hose to indicate its installation position.


HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used. (for HV Model)

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model)

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISABLE BRAKE CONTROL (for HV Model)

Z101186

Click here(Click here)

Hide 3.REMOVE REAR WHEEL

Hide 4.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 47319F 5.REMOVE REAR FLEXIBLE HOSE

a.
C445714N02
1.906,0.073 2.656,0.396 0.75,0.323 18 true i, ii, iii

i.

Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.


ii.

Using a union nut wrench, disconnect the brake line while holding the rear flexible hose with a wrench.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




iii.

Remove the clip and rear flexible hose from the vehicle body.