Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2021.07
RM3700E _55 Steering _093027 POWER ASSIST SYSTEMS _0442429 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C155A16  Power Steering Motor "A" Supply Voltage Circuit Voltage Below Threshold  C155B16  Power Steering Motor "B" Supply Voltage Circuit Voltage Below Threshold  


DESCRIPTION

If a problem occurs in the system, the power source relay circuit and the motor relay circuit are shut off to stop power assist. The ECU must be replaced when there is a problem with the relays because the relays are built into the ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Return-to-normal Condition Note
C155A16 Power Steering Motor "A" Supply Voltage Circuit Voltage Below Threshold Motor "A" PIG voltage is 3.5 V or less
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU assembly


EPS warning light: Comes on EMPS A Ignition switch ON again -
C155B16 Power Steering Motor "B" Supply Voltage Circuit Voltage Below Threshold Motor "B" PIG voltage is 3.5 V or less
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU assembly


EPS warning light: Comes on EMPS A Ignition switch ON again -

WIRING DIAGRAM

C322363E71
5.479,2.958 6.771,3.375 1.292,0.417 10 false Power Steering ECU Assembly 1.458,0.708 3.177,1.083 1.719,0.375 10 false from Auxiliary Battery 3.833,0.896 4.375,1.156 0.542,0.26 10 false EPS 5.677,0.74 6.219,1 0.542,0.26 10 false PIG 5.677,1.906 6.219,2.167 0.542,0.26 10 false PGND 5.51,0.625 6.052,0.885 0.542,0.26 10 false 1 5.5,1.792 6.042,2.052 0.542,0.26 10 false 2 5.479,2.792 6.021,3.052 0.542,0.26 10 false H2

CAUTION / NOTICE / HINT

NOTICE:
·

When the power steering ECU assembly has been replaced, perform Power Steering ECU Initial Setting (assist map writing).

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for HV Model A
for Gasoline Model B



A

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the H2 power steering ECU assembly connectors.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H2)Location & Routing

Click Connector(H2)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Steering ECU with Motor Assembly

H2-1 (PIG) - Body ground Ignition switch ON (READY), power assist in operation 8 to 16 V



Procedure2

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H2)Location & Routing

Click Connector(H2)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Steering ECU with Motor Assembly

H2-2 (PGND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the H2 power steering ECU assembly connectors.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H2)Location & Routing

Click Connector(H2)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Steering ECU with Motor Assembly

H2-1 (PIG) - Body ground Engine running, power assist in operation 8 to 16 V



Procedure2

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H2)Location & Routing

Click Connector(H2)Instrument Panel>Instrument Panel Wire / Speaker Wire>Power Steering ECU with Motor Assembly

H2-2 (PGND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR