Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING ECU › from 2021.07
RM3700E _55 Steering _093027 POWER ASSIST SYSTEMS _0438530 POWER STEERING ECU A

POWER ASSIST SYSTEMS  POWER STEERING ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C459800N01
0.823,0.073 6.25,3.719 5.427,3.646 4.667,0.188 5.885,1.813 1.219,1.625 5.396,0.375 5.688,0.375 false 6.25,1.938 6.583,1.938 false 5.292,1.813 5.292,1.99 false 1.781,2.208 1.948,2.208 1.948,2.208 1.948,2.625 false 2.74,0.948 3.323,0.948 false 2.604,3.354 2.417,3.583 2.417,3.583 2.25,3.583 false 3.688,1.854 4.021,1.854 false 4.906,2.875 4.573,2.875 false 5.729,0.271 5.885,0.469 0.156,0.198 10 false ● 6.615,1.802 6.896,2.156 0.281,0.354 18 false 1 5.323,1.958 5.604,2.313 0.281,0.354 18 false 2 1.583,2.042 1.865,2.396 0.281,0.354 18 false 3 2.552,0.823 2.833,1.177 0.281,0.354 18 false 4 5.438,0.385 5.75,0.583 0.313,0.198 10 false x2 3.615,0.438 3.927,0.635 0.313,0.198 10 false x3 4.083,1.75 4.24,1.948 0.156,0.198 10 false ● 1.938,3.479 2.552,3.677 0.615,0.198 10 false ● *2 4.729,0.25 5.104,0.49 0.375,0.24 12 false *A 4.948,2.781 5.563,2.979 0.615,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STEERING COLUMN ASSEMBLY - - - -
2 STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY 45020B (Click here) - -
3 BRACKET - (Click here) - -
4 POWER STEERING ECU ASSEMBLY 89650 (Click here) - -

*A w/ Entry and Start System - -
*1 ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY *2 CLIP BAND
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the power steering ECU assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Power steering ECU assembly Assist map writing
·

DTCs are stored

·

EPS warning light illuminates

·

Vehicle control history (RoB) are stored


(Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)

HINT:
·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure as for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1.REMOVE STEERING COLUMN ASSEMBLY

Hide 45020B 2.REMOVE STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY (w/ Entry and Start System)

Z101186

Click here(Click here)

Hide 3.REMOVE BRACKET

a.
C459801N01
2.781,0.063 3.063,0.365 0.281,0.302 18 false iii 1.656,0.563 1.792,0.844 0.135,0.281 18 true i 6.333,1.146 6.542,1.427 0.208,0.281 18 true v 6.5,1.427 6.708,1.688 0.208,0.26 18 true iv 3.063,0.365 3.25,0.615 0.188,0.25 18 true ii 1.906,0.823 2.115,1.104 0.208,0.281 18 true iii 2.406,0.833 2.615,1.115 0.208,0.281 18 true iii 2.427,1.396 2.635,1.677 0.208,0.281 18 true iii 2.125,0.083 2.333,0.365 0.208,0.281 18 true iii

i.

Remove the screw.


ii.

Cut the clip band.

NOTICE:

Do not damage the wire harness when cutting the clip band.



iii.

Disconnect the connectors and disengage the clamps.


iv.

Using a 5 mm hexagon socket wrench, remove the bolt.


v.

Disengage the guide to remove the bracket from the electric power steering column sub-assembly.



Hide 89650 4.REMOVE POWER STEERING ECU ASSEMBLY

Z101186

NOTICE:
·

Do not drop the power steering ECU assembly, strike it with tools or subject it to impacts.

·

If the power steering ECU assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness of the steering column assembly.

·

Do not allow any moisture to come into contact with the power steering ECU assembly.

·

Do not loosen any bolts not mentioned in the procedure.

·

Do not allow any foreign matter to contaminate the power steering ECU assembly.




a.
C459802N01
1.927,0.188 2.208,0.542 0.281,0.354 18 false i 4.135,0.188 4.417,0.542 0.281,0.354 18 false ii

i.

Using a 4 mm hexagon socket wrench, remove the 3 bolts and power steering ECU assembly from the electric power steering column sub-assembly.


ii.

Remove the O-ring from the power steering ECU assembly.