Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Adaptive High Beam System) › from 2021.07
RM3700E _59 Vehicle Exterior _093283 LIGHTING (EXT) _0486937 LIGHTING SYSTEM(w/ Adaptive High Beam System) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Adaptive High Beam System)  Daytime Running Light Circuit  


DESCRIPTION

When the operation conditions of the daytime running lights are met, the main body ECU (multiplex network body ECU) sends an illumination request signal to the headlight ECU sub-assembly and illuminates the daytime running lights.

WIRING DIAGRAM

E440258E02
1.167,6.198 3.135,6.51 1.969,0.313 10 false : CAN Communication Line 0.094,5.354 1.469,5.927 1.375,0.573 10 false Semiconductor Power Integration Computer 1.813,5.031 2.469,5.208 0.656,0.177 10 false A111 1.802,5.208 4.104,5.604 2.302,0.396 10 false Headlight ECU Sub-assembly RH 0.885,4.646 1.542,4.823 0.656,0.177 10 false L 1.146,4.656 1.802,4.833 0.656,0.177 10 false A86 1.208,4.458 1.865,4.635 0.656,0.177 10 false 2 2.073,4.667 2.729,4.844 0.656,0.177 10 false ECUB 3,3.969 3.656,4.146 0.656,0.177 10 false GND 2.938,4.656 3.594,4.833 0.656,0.177 10 false RLD2 1.823,4.542 2.479,4.719 0.656,0.177 10 false 13 3.375,3.844 4.031,4.021 0.656,0.177 10 false 12 3.396,4.521 4.052,4.698 0.656,0.177 10 false 8 4.125,4.656 4.781,4.833 0.656,0.177 10 false DRLC 3.917,5.635 4.573,5.813 0.656,0.177 10 false 2 4.135,5.729 4.792,5.906 0.656,0.177 10 false B 4.01,6.104 4.667,6.281 0.656,0.177 10 false B13 4.01,6.281 6.708,6.49 2.698,0.208 10 false Daytime Running Light Assembly RH 3.927,4.542 4.583,4.719 0.656,0.177 10 false 4 6.156,5.74 6.813,5.917 0.656,0.177 10 false E 6.396,5.604 7.052,5.781 0.656,0.177 10 false 1 4.667,3.417 6.333,4.063 1.667,0.646 10 false Main Body ECU (Multiplex Network Body ECU) 1.958,1.906 2.615,2.083 0.656,0.177 10 false A110 1.958,2.073 4.49,2.354 2.531,0.281 10 false Headlight ECU Sub-assembly LH 1.135,0.719 1.792,0.896 0.656,0.177 10 false A86 0.896,0.719 1.552,0.896 0.656,0.177 10 false L 1.229,0.51 1.885,0.688 0.656,0.177 10 false 1 4.052,1.01 4.708,1.188 0.656,0.177 10 false B12 4.052,1.167 6.75,1.375 2.698,0.208 10 false Daytime Running Light Assembly LH 6.417,0.542 7.073,0.719 0.656,0.177 10 false 1 6.188,0.677 6.844,0.854 0.656,0.177 10 false E 4.125,0.271 4.781,0.448 0.656,0.177 10 false B 3.896,0.188 4.552,0.365 0.656,0.177 10 false 2 4.115,0.729 4.771,0.906 0.656,0.177 10 false DRLC 3.917,0.615 4.573,0.792 0.656,0.177 10 false 4 3.396,0.615 4.052,0.792 0.656,0.177 10 false 8 2.948,0.698 3.604,0.875 0.656,0.177 10 false RLD2 2.99,1.531 3.646,1.708 0.656,0.177 10 false GND 3.385,1.427 4.042,1.604 0.656,0.177 10 false 12 1.792,0.604 2.448,0.781 0.656,0.177 10 false 13 2.083,0.729 2.74,0.906 0.656,0.177 10 false ECUB

CAUTION / NOTICE / HINT

NOTICE:
·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>INITIALIZATION

·

When replacing the headlight ECU sub-assembly LH, always replace it with a new one. If a headlight ECU sub-assembly LH which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK LIGHTS
a.

Check the illumination of each clearance lights and daytime running lights.


Result:
Result Proceed to
LH side daytime running light does not illuminate A
RH side daytime running light does not illuminate B



A

2.PERFORM ACTIVE TEST USING GTS

B

6.PERFORM ACTIVE TEST USING GTS
2.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Headlight Control > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Daytime Running Light Daytime running light LH ON -
Body Electrical > Headlight Control > Active Test
Tester Display
Daytime Running Light
50004 462 5
OK:

Daytime running lights illuminate.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.INSPECT DAYTIME RUNNING LIGHT ASSEMBLY LH
3.INSPECT DAYTIME RUNNING LIGHT ASSEMBLY LH

OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE - DAYTIME RUNNING LIGHT ASSEMBLY LH)

NG

REPLACE DAYTIME RUNNING LIGHT ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE - DAYTIME RUNNING LIGHT ASSEMBLY LH)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B12)Location & Routing

Click Connector(B12)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LH

B12-2 (B) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY LH)
a.

Disconnect the A110 headlight ECU sub-assembly LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B12,A110)Location & Routing

Click Connector(B12)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LH

Click Connector(A110)Engine Compartment>Engine Room Main Wire>Headlight ECU Sub-Assembly LH

B12-4 (DRLC) - A110-8 (RLD2) Always Below 1 Ω
B12-1 (E) - Body ground Always Below 1 Ω
B12-4 (DRLC) - Body ground Always 10 kΩ or higher
A110-8 (RLD2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Headlight Control > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Daytime Running Light Daytime running light LH ON -
Body Electrical > Headlight Control > Active Test
Tester Display
Daytime Running Light
50004 462 5
OK:

Daytime running lights illuminate.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

7.INSPECT DAYTIME RUNNING LIGHT ASSEMBLY RH
7.INSPECT DAYTIME RUNNING LIGHT ASSEMBLY RH

OK

8.CHECK HARNESS AND CONNECTOR (POWER SOURCE - DAYTIME RUNNING LIGHT ASSEMBLY RH)

NG

REPLACE DAYTIME RUNNING LIGHT ASSEMBLY RH

8.CHECK HARNESS AND CONNECTOR (POWER SOURCE - DAYTIME RUNNING LIGHT ASSEMBLY RH)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B13)Location & Routing

Click Connector(B13)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RH

B13-2 (B) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT ASSEMBLY RH - HEADLIGHT ECU SUB-ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT ASSEMBLY RH - HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Disconnect the A111 headlight ECU sub-assembly RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B13,A111)Location & Routing

Click Connector(B13)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RH

Click Connector(A111)Engine Compartment>Engine Room Main Wire>Headlight ECU Sub-Assembly RH

B13-4 (DRLC) - A111-8 (RLD2) Always Below 1 Ω
B13-1 (E) - Body ground Always Below 1 Ω
B13-4 (DRLC) - Body ground Always 10 kΩ or higher
A111-8 (RLD2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR